MetalworkingFun Forum › Machinery › Lathes v
[HELP] What's mt taper?

Thread Modes
Help What's mt taper?
texx Away
Freshman
**
Posts: 37
Threads: 3
Joined: May 2014
Location: australia
The following 1 user Likes texx's post:
Andy T (06-07-2017)
#11
06-06-2017, 05:34 PM
link to a thread in another forum with some info .

http://chaski.org/homemachinist/viewtopic.php?t=48749
texx, proud to be a member of MetalworkingFun Forum since May 2014.
Reply
Thanks given by: Andy T
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#12
06-06-2017, 06:06 PM
Do you need to use the taper? My Summit has a #6 MT, came with a sleeve to #5 but I've never used it. When I want to turn between centres I chuck a piece of scrap and cut a 60 deg point on it. Zero runout then.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: Andy T
Andy T Offline
Freshman
**
Posts: 30
Threads: 4
Joined: May 2017
Location: England
#13
06-07-2017, 04:06 AM
(06-06-2017, 06:06 PM)f350ca Wrote: Do you need to use the taper? My Summit has a #6 MT, came with a sleeve to #5 but I've never used it. When I want  between centres I chuck a piece of scrap and cut a 60 deg point on it. Zero runout then.

At this time I don't need to use the taper but the between centers distance is only around 12" so at some time an "every little helps" situation may arrise and I'd rather figure a solution now than leave it to a possible last minute suituation.
While searching Google for an answer I came across this pdf that has a vast amount of info but sadly none for me, http://cnqzu.com/library/Anarchy%20Folde...63_yg8.pdf
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#14
06-07-2017, 07:23 AM
What is the tailstock taper?

My old lathe had a 3" through hole with some form of taper that (like Greg's lathe) would have had an adaptor to make it useful. Like Greg, I've always just turned a piece of scrap to a taper when turning between centres.
Hunting American dentists since 2015.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
Andy T (06-07-2017)
#15
06-07-2017, 08:01 AM
My lathe must have an odd taper too. The manual lists the headstock taper as #6, but has a 3 inch through hole. According to the chart you posted the inside of the bushing must be #6.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Andy T Offline
Freshman
**
Posts: 30
Threads: 4
Joined: May 2017
Location: England
#16
06-07-2017, 08:39 AM
(06-07-2017, 07:23 AM)Mayhem Wrote: What is the tailstock taper?

My old lathe had a 3" through hole with some form of taper that (like Greg's lathe) would have had an adaptor to make it useful.  Like Greg, I've always just turned a piece of scrap to a taper when turning between centres.

It's a MT2, and I've now bored it through to 10mm so I can knock the tapers out.
I had to bore the minor dia a little deeper to 14mm to allow tapers with tangs, all's fine with the tailstock now Big Grin
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 1 user Likes Mayhem's post:
Andy T (06-07-2017)
#17
06-07-2017, 08:43 AM
Ah - yes! I remember now. At least one end is sorted!
Hunting American dentists since 2015.
Reply
Thanks given by:




Users browsing this thread: 4 Guest(s)