12-27-2015, 04:56 PM
Anybody have plans for a rod bender? I'd like to make one that can bend up to 1/2" mild steel rod. I've used Mr Google and found some but none that peaked my interest.
Ed
Ed
|
Rod Bender Plans
|
 
12-27-2015, 05:31 PM
Hi Ed,
They come in all sorts and sizes. To bend 1/2" it needs to be fixed well to something, you may be able to hold it in your vise (the bending jig) if the vise is suitability securely fixed. Or have you thought about using your press. Like this http://weldingweb.com/showthread.php?423...post399031  DaveH
a child of the 60's and 50's and a bit of the 40's
12-27-2015, 05:44 PM
Dave,
I would be fixing to an upright in the basement that's carrying the load of the house so it should be plenty stout. It's something that I'd set up as needed. Thanks for the link. I was looking at this one which might do 1/2" rod. I suppose I could beef it up to make sure it'll handle it though. http://oxtool.blogspot.com/2012/08/rod-bender.html Ed
12-27-2015, 08:06 PM
I've had this one for years Ed. It has Vee'd jaws for round stock and different dies for varying radius bends. Bends 1/2 round effortlessly, think its 1/4 x 4 flat it will bend. I have it mounted on a 2 inch square tube that goes into a receiver on one of the columns of the shop.
![[Image: 2910280.jpg?_v=5a94e708-b43a-47fc-b9d2-56110847a5a6]](http://images11.palcdn.com/hlr-system/WebPhotos/29/291/2910/2910280.jpg?_v=5a94e708-b43a-47fc-b9d2-56110847a5a6)
Free advice is worth exactly what you payed for it.
Greg Thanks given by: EdK
12-27-2015, 10:02 PM
(12-27-2015, 08:06 PM)f350ca Wrote: ..... I have it mounted on a 2 inch square tube that goes into a receiver on one of the columns of the shop. Any chance you could post a picture of that sometime Greg? I've been trying to figure out a way of mounting a flat bar bender in a non-permanent manor to a vertical I-beam. I'm liking your idea! 
Willie
12-28-2015, 12:58 AM
This isn't a great picture Willie but should give you some ideas.
![[Image: IMGP1255.jpg]](https://lh3.googleusercontent.com/-Mhoo1TTkoOY/S-XcXRo3VOI/AAAAAAAAAHw/c_9_-t4m084/s1440-Ic42/IMGP1255.jpg) There are two mounts here, the one the slip roll is in comes straight out from the column, the one the vice is in allows you to go cross wise. They're 2 1/2 square tube with a 3/16 wall, 2 inch square on the vise and slip roll slip in the same as a receiver hitch on a truck. They're cross drilled for a locking pin as well. Have mounts for these, the bender I mentioned and a motorized chuck for welding.
Free advice is worth exactly what you payed for it.
Greg Thanks given by: Highpower
12-28-2015, 05:19 PM
Thanks Greg.
 I'm liking the cross-wise receiver. The only thing is I don't want to weld anything directly to the I-beam. I guess I could make a "sandwich" using a couple pieces of plate steel with the beam in the middle, and tie them together with some threaded rod. Then I could just weld the receiver to one of the plates.  Great.... another project for the list.  
Willie
12-28-2015, 07:26 PM
And now, I'm thinking that I could use the sandwich idea to attach to one of the 6x6 posts in the garage. It would be easy enough to roll the wood shaper out of the way, and then I could get a bender...
You guys...
Mike
SB 10K (1976) Rockwell vertical mill (1967) Rockwell 17" drill press (1946) Me (1949) 
12-28-2015, 08:18 PM
I don't have any poles out here but I do have a press and that press version looks interesting. Don't have a need right now tho. Watch, now that I said that I'm gonna need one next week!
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop | the nobucks boutique 
01-28-2016, 08:24 PM
I made 3 of these...Bob http://kinzers.com/don/MachineTools/bender/
Bob Wright
Metal Master Fab Salem Ohio Birthplace of the Silver and Deming drill bit. 5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders... Thanks given by: Highpower
|
|
« Next Oldest | Next Newest »
|
Users browsing this thread: 2 Guest(s)