Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
(06-11-2015, 05:30 PM)Roadracer_Al Wrote: I like your risers. I had to put 6" risers on my Victor 16x40 to bring it up to adult height.
Whoa....you also have a Victor 1640 lathe?
I guess I missed the photos of it! I have one as well, though mine is probably in worse condition than many. It was free for the cost of shipping so I don't complain. I've never thought to put mine on risers as never felt as though it was uncomfortably short for my 5'10" height. Not a bad idea though, so how much did you pick it up?
Posts: 968
Threads: 67
Joined: Apr 2015
Location: Australia
Really nice workshop there Mike. I like the frame under your mill too, may have to go on the list...
Lathe (n); a machine tool used in the production of milling machine components.
Milling Machine (n); a machine tool used in the production of lathe components.
Posts: 173
Threads: 2
Joined: Jun 2015
Location: Utah
(06-11-2015, 04:50 PM)EdK Wrote: Mike,
I like the table guards you installed. What are they made of?
Thanks,
Ed
They are just some neoprene rubber that I bought from McMaster Carr. I need to make a couple of small blocks and either screw them or glue them to the back that fit into the table slots. They move around just a little bit, not bad, but enough that I want them to kind of "lock" into place a bit better. I notched around the mill vise bolts which helps to keep swarf out of the table slots as well but they do move more than I would like.
(06-11-2015, 05:30 PM)Roadracer_Al Wrote: I like your risers. I had to put 6" risers on my Victor 16x40 to bring it up to adult height.
Thanks. When I fabricated it I wanted the mill table to be at a comfortable working height as I hated how low my last lathe/mill machine was. I lived with it like that for 17 years and swore I was going to set these up properly from the get go and make them comfortable.
(06-11-2015, 06:54 PM)EdK Wrote: Speaking of height, what's the dimension from the floor to the table surface on that mill Mike? Minus your risers.
Thanks,
Ed
Ed, I will have to measure the spindle height and post it. I don't currently have that available. Obviously measuring the table height is not an accurate measurement because it moves vertically, but I will measure the spindle height for you. I am 6'2" and don't find myself bending over at all when using the mill. Had it been a full-size mill I would have still raised it a couple of inches to be comfortable. Our BP clone at work is a 9x49 and sits flat on the floor but it is a bit low, yet you have to reach for the drawbar so in that respect I am glad it isn't any higher.
(06-11-2015, 08:13 PM)arvidj Wrote: Looking at the riser ... it looks like it would be the perfect way to get a small pallet jack under the mill and then move it to other parts of the shop should the need arise.
Yes, I will be stealing this idea.
Steal away.
(06-12-2015, 04:11 AM)Pete O Wrote: Really nice workshop there Mike. I like the frame under your mill too, may have to go on the list...
Thank you.
Mike.
Posts: 8,891
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
Thanks Mike and good point on the table moving up and down. I didn't think of that since I've never owned a knee mill before. The spindle height will have to do then. I'm about 5'3" on most days so the height is a concern for me.
Thanks,
Ed
Posts: 173
Threads: 2
Joined: Jun 2015
Location: Utah
(06-12-2015, 10:23 AM)EdK Wrote: Thanks Mike and good point on the table moving up and down. I didn't think of that since I've never owned a knee mill before. The spindle height will have to do then. I'm about 5'3" on most days so the height is a concern for me.
Thanks,
Ed
I will measure it for you Ed, but with your height (or lack thereof  ) you may be fine with it standing directly on the floor.
Mike.
Posts: 8,891
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
(06-12-2015, 10:47 AM)zmotorsports Wrote: (06-12-2015, 10:23 AM)EdK Wrote: Thanks Mike and good point on the table moving up and down. I didn't think of that since I've never owned a knee mill before. The spindle height will have to do then. I'm about 5'3" on most days so the height is a concern for me.
Thanks,
Ed
I will measure it for you Ed, but with your height (or lack thereof ) you may be fine with it standing directly on the floor.
Mike.
I'm hoping that's the case. My welding sucks. 
Ed
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
The following 2 users Like DaveH's post:
f350ca (06-12-2015), Vinny (06-12-2015)
Posts: 173
Threads: 2
Joined: Jun 2015
Location: Utah
(06-12-2015, 10:23 AM)EdK Wrote: Thanks Mike and good point on the table moving up and down. I didn't think of that since I've never owned a knee mill before. The spindle height will have to do then. I'm about 5'3" on most days so the height is a concern for me.
Thanks,
Ed
Ed, I ran home at lunch and grabbed those measurements for you.
From the ground to the bottom of the spindle mine measures 55". This is sitting on a my base which is 8.5" tall.
At that height my table is in the 40"-45" for much of my smaller work.
I hope that helps you out on size/height.
Mike.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
The following 2 users Like DaveH's post:
Vinny (06-12-2015), f350ca (06-12-2015)
(06-12-2015, 02:28 PM)zmotorsports Wrote: I hope that helps you out on size/height.
Mike.
If not these should
Pink-yellow-platform.jpg_350x350.jpg (Size: 54.84 KB / Downloads: 131)
DaveH
Posts: 8,891
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
(06-12-2015, 02:28 PM)zmotorsports Wrote: (06-12-2015, 10:23 AM)EdK Wrote: Thanks Mike and good point on the table moving up and down. I didn't think of that since I've never owned a knee mill before. The spindle height will have to do then. I'm about 5'3" on most days so the height is a concern for me.
Thanks,
Ed
Ed, I ran home at lunch and grabbed those measurements for you.
From the ground to the bottom of the spindle mine measures 55". This is sitting on a my base which is 8.5" tall.
At that height my table is in the 40"-45" for much of my smaller work.
I hope that helps you out on size/height.
Mike.
Thanks Mike. That's what I needed.
Ed
|
