MetalworkingFun Forum › Machining › Projects v
[PROJECT] Spin Indexer Tailstock

Thread Modes
Project Spin Indexer Tailstock
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#131
12-19-2014, 05:55 PM
Nice finish Ed. What did you polish it out with? Looks way better. Its always hit and miss for me getting a nice finish when facing.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,890
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 1 user Likes EdK's post:
Mayhem (12-19-2014)
#132
12-19-2014, 06:31 PM
(12-19-2014, 05:55 PM)f350ca Wrote: Nice finish Ed. What did you polish it out with? Looks way better. Its always hit and miss for me getting a nice finish when facing.

No polish. Just used the correct tool this time and power feed. That insert is made for aluminum. Smile

Ed


   
Reply
Thanks given by: f350ca
EdK Offline
Whipping Boy
*******
Posts: 8,890
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 3 users Like EdK's post:
PixMan (12-26-2014), Mayhem (12-26-2014), Highpower (12-27-2014)
#133
12-26-2014, 06:34 PM
Got'r done, finally.  Big Grin

Ed

         


         


   
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#134
12-26-2014, 07:00 PM
I only see one minor problem with that tailstock Ed: It's 100 notches in quality above any Chinese spindexer that you'd use it with!
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,890
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#135
12-26-2014, 07:20 PM
(12-26-2014, 07:00 PM)PixMan Wrote: I only see one minor problem with that tailstock Ed: It's 100 notches in quality above any Chinese spindexer that you'd use it with!

Rotfl

My Phase II spin indexer is of reasonable quality so I think it's a good mate. I enjoyed making the tailstock and learned a few things.

On to the next project. Tom's clamp knurling tool.

Ed
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#136
12-26-2014, 07:51 PM
Top job Ed. I'm guessing the two lugs are to bolt it to the table. If so, I'm curious as to why they are not lower down.
Hunting American dentists since 2015.
Reply
Thanks given by: EdK
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#137
12-26-2014, 09:34 PM
Very nice Ed. How well does the split cotter grab?
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,890
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#138
12-26-2014, 09:37 PM
(12-26-2014, 07:51 PM)Mayhem Wrote: Top job Ed.  I'm guessing the two lugs are to bolt it to the table.  If so, I'm curious as to why they are not lower down.

I don't know why the designer has them at that height. But I'm not sure there's any advantage to having them lower, unless I'm missing something. Chin

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,890
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#139
12-26-2014, 09:38 PM
(12-26-2014, 09:34 PM)f350ca Wrote: Very nice Ed. How well does the split cotter grab?

Greg,

The split cotter grabs just fine. I can't advance the arbor at all if it's clamped so it must be doing its job. Smile

Ed
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#140
12-26-2014, 09:41 PM
Good to hear, I've always had them in a solid housing, wondered if they'd spring unsupported, good to know for future designs. Thanks
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 9 Guest(s)