MetalworkingFun Forum › Machinery › Lathes v
Lathe Cross Slide Problem

Thread Modes
Lathe Cross Slide Problem
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 1 user Likes EdK's post:
DaveH (06-24-2014)
#111
06-24-2014, 11:33 AM
(06-24-2014, 08:27 AM)DaveH Wrote: Clumsy ...................

Yes.

Quote:Looking for sympathy Rotfl
Smiley-eatdrink004
DaveH

No.

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
The following 1 user Likes Highpower's post:
Mayhem (06-24-2014)
#112
06-24-2014, 12:01 PM
What is with all this pre-planning and making perfect parts the first time Ed?
You are making us hacks that just "wing it" look bad. Rotfl

Smiley-signs107
Willie
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 3 users Like EdK's post:
Mayhem (06-24-2014), PixMan (06-24-2014), Highpower (06-24-2014)
#113
06-24-2014, 04:47 PM
(06-24-2014, 12:01 PM)Highpower Wrote: What is with all this pre-planning and making perfect parts the first time Ed?
You are making us hacks that just "wing it" look bad. Rotfl

Smiley-signs107

Willie,

Ken made one lead screw and one nut for my lathe so I have one chance to get it right. Smile

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#114
06-24-2014, 06:27 PM
Drew a little more blood this evening but not much. I managed to get the nut milled, with no blood stains. Tomorrow evening I'll work on attaching the gear to the lead screw. I almost forgot about that. Blush

Ed
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
The following 1 user Likes DaveH's post:
EdK (06-24-2014)
#115
06-24-2014, 06:49 PM
More blood Slaphead carry on like this Ed, you'll have none left Big Grin
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#116
06-24-2014, 07:24 PM (This post was last modified: 06-24-2014, 07:25 PM by PixMan.)
(06-24-2014, 04:47 PM)EdK Wrote: Willie,

Ken made one lead screw and one nut for my lathe so I have one chance to get it right. Smile

Ed

No worries though, Ed. If the worst happens I could make a second set in half the time, blindfolded. Big Grin
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#117
06-25-2014, 05:53 AM
Thanks Ken. I'll try my damnedest not to screw this up. I don't want to disrupt your summer riding experiences. Summers are too short as it is. Smile

Ed
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 3 users Like Mayhem's post:
DaveH (06-25-2014), EdK (06-25-2014), Highpower (06-25-2014)
#118
06-25-2014, 07:23 AM
Don't screw this up Ed - I have a half finished mill here...
Hunting American dentists since 2015.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#119
06-25-2014, 08:06 AM
The only part I'm concerned about at this point is mounting the nut accurately in line with the the lead screw path. Chin

Ed
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#120
06-25-2014, 02:56 PM
Ed, I dunno if I'm on track here or not but the following thought comes to mind.
With every thing assembled, the cross slide close to the operator (you) and the nut under the hole in the cross slide make a mark on the nut then slide the cross slide as far away from you and wind the nut under it and see if your reference mark lines up.
Chin
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:




Users browsing this thread: 14 Guest(s)