Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
First question, whats a wheelbarrow, is that one of those antique thing's that people who don't own tractors with loaders use.
Sasquatch brings up a good point, check the rpm, a 3400 rpm one will drive you to distraction. I have a twin tank one similar to the ones you posted, but its 1725 rpm. Has run for years with no maintenance, operating air nailers and general duty in the cabinet shop till I ran a line up from the machine shop.
Have you looked for a used industrial one. The big cast iron behemoths run for ever. I picked up a V4 two stage Devilibis for around $500 on auction, had to change out the 3 phase motor but lots of air and quiet.
Free advice is worth exactly what you payed for it.
Greg
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
(12-04-2012, 11:08 AM)f350ca Wrote: First question, whats a wheelbarrow, is that one of those antique thing's that people who don't own tractors with loaders use.
Yes.
Quote:Sasquatch brings up a good point, check the rpm, a 3400 rpm one will drive you to distraction. I have a twin tank one similar to the ones you posted, but its 1725 rpm. Has run for years with no maintenance, operating air nailers and general duty in the cabinet shop till I ran a line up from the machine shop.
Have you looked for a used industrial one. The big cast iron behemoths run for ever. I picked up a V4 two stage Devilibis for around $500 on auction, had to change out the 3 phase motor but lots of air and quiet.
I'm leery of used compressors unless the tank has been inspected by someone that knows what they are doing and can guarantee that the tank is not going to blow sky high in the near future. 
Plus, I'm not ready for a behemoth yet. No space set aside for one in the garage and no way in hell it would go in the basement.
I'll keep looking for one that's 1725 RPMs though to help cut down on the noise. I'm in no huge rush to get one, just a small rush. 
Ed
Posts: 576
Threads: 18
Joined: Feb 2012
Location: Washington State USA
12-04-2012, 12:26 PM
(This post was last modified: 12-04-2012, 12:31 PM by ETC57.)
Ed,
you mentioned you have a portable air tank, why not get a throwaway little portable compressor to hook to your tank for the a short term fix. Sense you have become used to not having a compressor this will improve your current situation, giving you some time to shop around.
If you go dc and get a little converter, when you do replace it you could keep the little compressor in your car for emergencies.
Just a thought.
Jerry.
ETC57, proud to be a member of MetalworkingFun Forum since Feb 2012.
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
This one looks interesting, but the cost is a bit higher than I wanted to go. 
http://www.northerntool.com/shop/tools/p..._200483164
Ed
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
Ed, Quincy has always been reckognized as top quality, but in today's world is a Quincy a Quincy? if it's a real Quincy I'd recommend it!
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
(12-04-2012, 04:07 PM)stevec Wrote: Ed, Quincy has always been reckognized as top quality, but in today's world is a Quincy a Quincy? if it's a real Quincy I'd recommend it!
It says it's made in the USA so I'm assuming it's the genuine deal, but at $600, that's a good chunk of the $1000 towards my real compressor so I'm back to looking at "cheap". Oh, my head hurts! 
Ed
Posts: 825
Threads: 25
Joined: Jul 2012
Location: N. Bay Ontario
Just a thought here:
I run an old compressor in my workshop, that is probably 30 + years old. I too was leary of the tank condition, so when i redid it, i adjusted the air pressure "MAX" to cut out at just 80 PSI.
At that pressure i have enough air for my purposes, i have no air tools, so use it mostly for blowing off parts, machines, the odd tire , etc.
I'm sure any used machines have a "MAX" adjusting screw, just cut it back if you don't want or feel comfortable with it pumping 125-175 psi. Just a thought.
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
12-04-2012, 05:06 PM
(This post was last modified: 12-04-2012, 05:07 PM by stevec.)
Hey Ed, is 7.1 CFM at 100 PSI below your requirements?
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
(12-04-2012, 05:06 PM)stevec Wrote: Hey Ed, is 7.1 CFM at 100 PSI below your requirements?
No, that's above my requirements, but I wouldn't mind having it. 
Ed
Posts: 139
Threads: 14
Joined: Apr 2012
Location: Nelson, BC, Canada
Ed
Too bad you weren't closer as I almost always have a compressor or two hidden in the pile here.
Walter
starlight_tools, proud to be a member of Metalworking Forum since Apr 2012.
|
