Posts: 432
Threads: 27
Joined: Feb 2016
Location: Woodstock:GA
The following 3 users Like pepi's post:
TomG (04-24-2017), f350ca (04-24-2017), Mayhem (04-25-2017)
04-24-2017, 08:03 AM
(This post was last modified: 04-24-2017, 08:07 AM by pepi.)
Rained all day, in need of some entertainment, decided to work out some problems. That the fire breathing weed eater I cobbled up had to be solved .
The lathe shines here for this type of deal, went to HD found a steel peg of some sort stored with the rebar, 3/4 x 2.5, 6 bucks.
Back home, commenced playing, first extend the wand ruffly a foot, no more leaning over. That and 6 bucks, some junk wheels, a lathe, some axel and bearing sizing, and welding kept me entertained for a rainy day.
Was a good day, I can tell you that.....
Greg
Woodstock's answer to agent orange
Magazines have issues, everything else has problems
Posts: 2,618
Threads: 100
Joined: Dec 2014
Location: Michigan
The following 1 user Likes Vinny's post:
Mayhem (04-25-2017)
Finished it over the weekend. The only thing left is to clean up and paint the three drawers that go in the front. Right now they're a nasty dirty scratched up green.
Posts: 2,618
Threads: 100
Joined: Dec 2014
Location: Michigan
The following 4 users Like Vinny's post:
EdK (05-03-2017), f350ca (05-03-2017), Mayhem (05-04-2017), DaveH (05-07-2017)
The above mill stand is now finished, drawers, shelf, levelers and all. After that I had to tear out a 3' x 8' bench that was never meant to come out, but it's gone - found a few things I'd been looking for under it too! The mill is on this new stand and the stand is in place. Pic are in its project thread.
That cleared up some space for the kick press to come in. Hoping to do that Saturday. On the wall, however, above that old bench, were a bunch of shelves where I had things (tools, etc) for the mini-lathe, mill, and just other junque. Well it had to go somewhere, besides that round cylinder with the plastic liner, so I built this. Still need to finish the front and put the door on, but in finishing it up last nite I managed to strain a hamstring so this part is slowing down. This getting old ***** sucks! I did manage to get two of the shelves down with the items on it either in this new cabinet, in one of the drawers of the other cabinet or the mill stand, or in the aforementioned cylinder.
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
The following 3 users Like EdK's post:
Mayhem (05-06-2017), f350ca (05-07-2017), DaveH (05-07-2017)
Cut up the wood for bins to store small stock. Got one assembled, the others will have to wait for another day.
Ed
Posts: 2,618
Threads: 100
Joined: Dec 2014
Location: Michigan
Looks good. I'm going to have to do something similar in the not too distant future.
On another note, I got the press in the shop finally and of course it was an adventure. I went to pick it up with the hilo and one of the hydraulic lines blew - the one for tilt. So I could still lift things, but everything lifted slid right off the forks. Eventually I slid it on all the way and strapped it to the front of the forks and lifted. Got it just inside the overhead door where a moving dolly was waiting for it. Set it down on the dolly and went to move the hilo. Nope, fork frame was too far forward and picked up part of the ramp in front of the door so it won't move. After a bit of swearing I got it backed up and parked it.
Back inside I rolled the press over to where it would live and in trying to get it off the dolly it must have been tired 'cuze it decided to lay down. Too heavy to lift and I ain't gettin the hilo in here. Found a long heavy pipe, used the leverage to stand it back up again and walked it back where it needed to go. At that point I decided that was enough for one day.
No pics, ain't even goona try. There's no tellin what may break next.
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
Sounds like quite the adventure Vinny. However, no pics = no like
Hunting American dentists since 2015.
Posts: 2,618
Threads: 100
Joined: Dec 2014
Location: Michigan
The following 2 users Like Vinny's post:
EdK (05-07-2017), f350ca (05-07-2017)
If I try to take a pic, the camera will break, then I'll plug it into the computer and it'll break, then ...
Posts: 432
Threads: 27
Joined: Feb 2016
Location: Woodstock:GA
So it all started here...... what's the puddle? Looking around it was dripping from the shock mount, and only after parked for a few days. Sniff test indicated gear oil.
A little labor and wrenching later
Add a furniture dolly and a manly push, it arrives at the shop door
Drag it over to the chain fall, a lift onto jack stands, a portable work bench is established. Upending and finding the wet spot. Found on the inside of the lower control arm axle bracket. Welder took care of it. So it sits ready to be installed, could do that after work, but may just wait for the weekend. Ants in the pants will be the decision maker for that
I pound on the car for sport from time to time and these things happen. To own any modified car one is way better off having the tools and whatever to fix this.
Cheers
Greg
Magazines have issues, everything else has problems
Posts: 642
Threads: 14
Joined: Oct 2013
Location: East Sussex, UK
You did of course drain the oil, totally dismantle and clean the axle casing and purge all hydro-carbons before welding, didn't you
..... you didn't
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
The following 1 user Likes Roadracer_Al's post:
Mayhem (05-12-2017)
(04-27-2017, 10:38 PM)Pete O Wrote: Upending and finding the wet spot.
Sounds like a great weekend!
|