US vs. UK (ER32 collet blocks)
#1
I've finally gotten around to getting myself a set of ER32 collets and a couple of chucks (R-8 and straight shank.) But I also wanted to get a set of square / hex collet blocks as well. Apparently the only thing available in the US now are all Chinese imports? 17428

So rather than do the usual roll of the dice with ebay I just ordered a couple of blocks (most likely Chinese) from Little Machine Shop in California.
5 day shipping that costs $14.37 with a grand total of approx $88.00

Then I find a set of "Stevenson" blocks at Arc Euro trade (UK) that come with ball bearing nuts as opposed to the plain nuts from China.
2 day shipping at a cost of $20.00 with a grand total of approx $68.00

I'll have to compare the sets when I get them to see how well they are made. I may keep both sets - or I may not. We'll see. Chin
Willie
Reply
Thanks given by:
#2
I bought the Stevenson blocks from Arc. Great quality, but probably made in China.
Micromark 7x14 Lathe, X2 Mill , old Green 4x6 bandsaw
The difficult takes me a while, the impossible takes a little longer.
Reply
Thanks given by:
#3
(05-07-2019, 02:31 PM)chucketn Wrote: I bought the Stevenson blocks from Arc. Great quality, but probably made in China.

Hmmm.... I wouldn't have thought so with John being in the UK. That is, if it's the same ("Sir") John Stevenson I'm thinking of.   Chin
Maybe not since I don't know the full history on his designs. I still want to compare them and check tolerances though.

I know the bearing nut on my Iscar R-8 chuck feels much nicer than the (China) plain nut on my straight shank chuck.

Edit to add:
After looking over some older posts on another forum it does appear that Arc was the deciding factor on if and where John's designs would be produced - which could be anywhere I suppose. I just assumed they were made in the UK.
https://www.model-engineer.co.uk/forums/...131257&p=3
Willie
Reply
Thanks given by:
#4
Before he died John went to China with Ketan from Arc Eurotrade to amongst other things discuss the drill sharpener that looks like a Moon Lander. The one they were selling was made to their specification and quality. I'd be surprised if the 'Sevenson' collet blocks hadn't followed the same process.

The Chinese will make things to as good quality as you want if you are prepared to pay
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by: Highpower
#5
I agree Andrew. I don't mind paying for a QUALITY tool, no matter where it comes from. I just hate paying premium prices for junk when it's the only thing readily available.

I'm on my way now to yet another doctors appointment - so I will have to stop at FedEx on my way home again to pick up the Stevenson blocks. Perhaps this will actually be more of a China vs. China comparison. Although it still irks me that I can get similar tools cheaper and faster from GB than I can here in the US.
Willie
Reply
Thanks given by:
#6
https://www.banggood.com/Hard-Steel-Hex-...rehouse=CN

https://www.banggood.com/Hard-Steel-Squa...rehouse=CN

Free Shipping.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
#7
Yeah, even cheaper via eBay. https://www.ebay.com/itm/Hex-ER-32-Colle...SwwppcwDTV

Unfortunately I wasn't looking for inexpensive, I was looking to pay more to get concentricity and repeatability.
I should get the LMS blocks today and I can start measuring things.
Willie
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)