Home Shop Made Tools
(06-18-2016, 08:39 AM)Jim1611 Wrote:
(06-17-2016, 09:09 PM)TomG Wrote: Nice job. It's always fun to pull out the steady.

Tom

Thanks Tom. I rarely use it but when it's needed nothing takes it's place.


(06-18-2016, 07:23 AM)pepi Wrote: I do not believe I have seen a 6 jaw chuck before, cool love learning. That is a nice looking steady, even better it was built by the owner.

Thanks pepi. I tend to build most everything extra like this, I enjoy it. The 6 jaw is a Cushman. It's also a scroll chuck too so the center can be adjusted. It's been great to have.

Hi JIM
Was also admiring Your 6 Jaw Chuck
Just curious what mounting to spindle ???
Is it Camlock or your USA styled ???
aRM
Reply
Thanks given by:
Six jaw chucks are wonderful. They chuck work nearly as concentric as collets, except they are infinitely adjustable. I have a Buck six jaw on my lathe and about the only time I'll resort to collets is if I'm doing a large number of parts.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
(06-18-2016, 11:16 AM)aRM Wrote: Hi JIM
Was also admiring Your 6 Jaw Chuck
Just curious what mounting to spindle ???
Is it Camlock or your USA styled  ???
aRM

It's a camlock. Here's a shot of the one I made for my 4 jaw chuck.

[Image: OtGs6u.jpg]


(06-18-2016, 11:41 AM)TomG Wrote: Six jaw chucks are wonderful. They chuck work nearly as concentric as collets, except they are infinitely adjustable. I have a Buck six jaw on my lathe and about the only time I'll resort to collets is if I'm doing a large number of parts.

Tom

They are great to use. Mine won't hold anything smaller than 3/8" dia. so I have to use collets for that size and under.
Reply
Thanks given by:
My Logan came with a Buck 6 jaw which by itself is worth close to 50% of the value of the lathe. Hadn't had the opportunity to use one in years and its great.
Reply
Thanks given by:
(06-18-2016, 10:50 PM)Dr Stan Wrote: My Logan came with a Buck 6 jaw which by itself is worth close to 50% of the value of the lathe.  Hadn't had the opportunity to use one in years and its great.

Wonder if we would be able to get one in a D1-6 CAMLOCK ???
Then again converting over some 15 times would be a reeeeeeeal killer for us !!!
aRM
Reply
Thanks given by:
I've used 6-jaw chucks before but never really felt to be lacking because I don't own one. My D1-6 mount 10" Pratt-Burnerd Super Precision 3-jaw chuck runs with less than 0.0005" runout with anything it can hold, regardless of size or orientation of the top jaws. When I did use the very nice 6-jaw chucks I found that not all the jaws exert the same pressure. I know this may have been just the one I was using. The way I found this was using 6 little squares of 0.003" brass shim stock to protect the finished surface I was clamping and two of them (not opposite each other) had fallen out while I was working the part.

When you only have three, all have to be clamping at equal pressure. ;)
Reply
Thanks given by:
From what I can gather 6 jaw chucks come into their own for holding thin wall tubing. But what I have not ever seen is an explanation of WHY that is. Smiley-think005
Willie
Reply
Thanks given by:
(06-20-2016, 01:59 PM)Highpower Wrote: From what I can gather 6 jaw chucks come into their own for holding thin wall tubing. But what I have not ever seen is an explanation of WHY that is.   Smiley-think005

With a three jaw the tube becomes triangular, six jaw it becomes hexagonal ............... looks much better Big Grin Big Grin Big Grin
Smiley-eatdrink004
DaveH
 a child of the 60's and 50's and a bit of the 40's Smile
Reply
Thanks given by:
A six jaw puts half the force of a three jaw on the work, so less distortion and less marring.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by: Highpower
6820

Do they use a different pitch on the scrolls or something? I'm thinking you'd get more juice from an orange if there were 4 hands squeezing it than 2 hands. 17428

Dave: Sounds like you need an 8-jaw chuck! Big Grin
Willie
Reply
Thanks given by:




Users browsing this thread: 17 Guest(s)