Wood to metal cutting conversion of vertical bandsaw
#1
I bought a 1/4hp motor with an 18:1 built in reduction drive on Kijiji (canadian craigslist) and it basically bolted into my Trademaster vertical bandsaw with no modifications aside from boring out an old pulley I had to fit the 3/4" shaft. I need to do some testing to sort out exactly what sfm I'm running the blade at currently but it's cutting steel nicely. From experience and feel I think I might be running a bit slow but I'm never in much of a rush anyways and at least I won't be burning up blades. 

[Image: image.jpg]


[Image: image.jpg]
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:
#2
Cool conversion! With that much gear reduction, it'll have lots of torque, too.
Reply
Thanks given by:
#3
Nice job Thumbsup 
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
#4
I have a 15:1 gearbox that I was thinking of using as the primary reduction for my vertical bandsaw. It runs fine on the belt drive countershaft, but we need to play, don't we? I just hope I get both of them back when I'm back in my house.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:
#5
I just found a three phase 1HP motor with a 7:1 reduction on it.  I'm thinking of converting a wood cutting bandsaw that I have. 

   

The fan cover is off, as I had to mark one of the blades to figure out the ratio.  The will result in about 195 rpm, so I'll have to look at the pulley size on the bandsaw and work out what SFM I will end up with.
Hunting American dentists since 2015.
Reply
Thanks given by:
#6
I'd actually like to use my bandsaw for cutting both wood and metal. Can you get the speed range required by using a three phase motor and a VFD?
Arbalest, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:
#7
(03-22-2015, 04:24 AM)Mayhem Wrote: I just found a three phase 1HP motor with a 7:1 reduction on it.  I'm thinking of converting a wood cutting bandsaw that I have. 



The fan cover is off, as I had to mark one of the blades to figure out the ratio.  The will result in about 195 rpm, so I'll have to look at the pulley size on the bandsaw and work out what SFM I will end up with.

The nice thing about converting is it's usually mostly lathe work to make or modify pulleys and shafts. That's one machine you have which is operable. Big Grin

Best of luck to you.

Nice work on your conversion, Shawn!
Reply
Thanks given by:
#8
Smart arse Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
#9
Nice conversion. I need to slow mine down too, but I will take the route of a dc motor which I picked up a while ago for $100.
Steve S
Check out MyShopNotes on youtube.
Reply
Thanks given by:
#10
Well, I took a different and somewhat more comical approach with my Toolkraft (of Springfield, Massachusetts) 14" bandsaw.  I used pulleys.

This what I posted somewhere at the time:

The saw in the first picture is a ToolKraft 14" Wood/Metal bandsaw. It was in good working order and clean when I bought it for $85.00. It doesn't look like it was ever used very much. It seems to be a copy more or less of the Delta Rockwell 28-200. Toolkraft was headquartered in Springfield and had a smaller plant in Enfield CT. It closed in 1984. This saw was made in Enfield.

   

I don't have a picture of the top pulley. Originally there was one belt that ran from the motor to the pulley running the wheels. That ran too fast to cut steel.

   

I added the large pulley and replaced the cone pulley on the motor with a 1 3/4" pulley, which was the smallest I could find. I created an Excel spreadsheet with the necessary formulas then ran it for different size pulleys. I got it down to 118 feet per minute.

   

I made an aluminum shaft from an old GP small pole. I mounted it through four brass bushings I had on hand. I made a support out of two pieces of 2"X4". About the largest wheel I could use was 10". To get the smallest diameter to drive the belt going to the saw I used the 3/4" shaft itself. The belt going to the saw runs between two additional bushings that each have two set screws...The 2"X4" supports are in turn supported by a cross piece I installed. I made it from a piece of iron bed frame. I have it attached to the saw frame with one bolt on each side. These are set up to provide tension adjustment to the second belt.

   


Charles
Charles Spencer, proud to be a member of MetalworkingFun Forum since Aug 2014.
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)