MetalworkingFun Forum › Machining › General Metalworking Discussion v
Before and after, drill press vise.

Thread Modes
Before and after, drill press vise.
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
The following 7 users Like Shawn's post:
Highpower (09-11-2014), EdK (09-11-2014), PixMan (09-11-2014), DaveH (09-11-2014), kenne (09-11-2014), Mayhem (09-11-2014), stevec (09-12-2014)
#1
09-11-2014, 11:23 AM
Just a simple wire wheel and spray can job.

[Image: image.jpg]

[Image: image.jpg]

Shawn
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:
mfletch Offline
Sophmore
***
Posts: 79
Threads: 12
Joined: Dec 2013
Location: mansfield UK
#2
09-11-2014, 11:40 AM
Wow you've done a cracking job of that
mfletch, Try to do the best you can and that's good enough
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,795
Threads: 183
Joined: Jun 2012
Location: Farmington Hills, Michigan
#3
09-11-2014, 12:00 PM
Very nice Shawn.

It doesn't appear to have seen much use. Looks like it just sat around collect dust for most of its life.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Micktoon Offline
Junior
****
Posts: 638
Threads: 43
Joined: Sep 2012
Location: England
#4
09-11-2014, 12:36 PM
Top job Shawn , nice to see decent tools come back to life Drool

cheers Mick
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:
doubleboost Offline
Super Moderator
******
Posts: 1,459
Threads: 159
Joined: Feb 2012
Location: Northern England
#5
09-11-2014, 03:22 PM
Very nice
In real good condition
John
http://www.youtube.com/user/doubleboost
Reply
Thanks given by:
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
#6
09-11-2014, 03:36 PM
Thanks gents, if I had to guess I would say it was never used or sparingly at best. Not bad for $5.00 and a couple hours to clean it up.

Shawn
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
#7
09-11-2014, 05:01 PM
a job well dun
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
schor Offline
Sophmore
***
Posts: 190
Threads: 17
Joined: Aug 2014
Location: Ajax Ontario Canada
#8
09-11-2014, 05:19 PM
Great job and a fantastic price.
Steve S
Check out MyShopNotes on youtube.
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#9
09-11-2014, 09:36 PM
Nice vise, better price!

I have a Starrett 5" bench vise in my home shop (not my machine shop) and it's got the same or very similar speckled finish blue paint. I think you would have been fine to simply clean off the rust and give the paint a good wipe-down, but hey, whatever floats yer boat. Looks great!
Reply
Thanks given by:
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
#10
09-12-2014, 01:32 AM
I wasn't going to paint it at all when I first started but the paint was worse than it looked and it gave me a chance to try out the colour. I may paint a lathe flat black this winter so a test run was in order.
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)