Thin grooving tools?
#11
(02-08-2014, 08:00 PM)f350ca Wrote: I was given a grooving tool and some inserts, think I've only used it once, the only time the insert matched the groove I needed.

Can't you move the cutter laterally and make the groove as wide as you want it? Unless the insert is wider than the groove you want of course.
Willie
Reply
Thanks given by:
#12
These are fairly big Willie, would have to look but think they're 1/8 and 3/16 inserts. The last ones I needed were .030.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#13
Ah yes. Gottcha Greg. That's exactly why I asked about the thin grooving tools. I have a couple of parting tools that I always wished they were thinner. It sounds like the Nikcole set that Ed and Russ have pretty much fills the bill in that area. And I just discovered that they have threading inserts for them as well. At that point resistance was futile and I placed the order.

I really should change my grinder back to normal someday. Blush
Willie
Reply
Thanks given by:
#14
Follow-up question:

I finally got the Nikcole set after the US postal slow system delivered it to the wrong address for the umpteenth time. (How do you go about getting an inept mail carrier reassigned to a different route???) Rant

Anyway... I was just looking online at the 'GP' grooving and cut-off inserts. I don't see any information about what the maximum diameter is for these cut-off inserts. They don't look any longer than the standard grooving inserts. 17428 17428 17428

Looks like the timing was right for me though. Victor's site shows "Last chance at the old price". ($116)
Willie
Reply
Thanks given by:
#15
Hi Willie,
According to http://www.mscdirect.com/browse/Indexabl...4287902322
Max depth of cut is 6mm (0.2362")
Smiley-eatdrink004
DaveH
Reply
Thanks given by: Highpower
#16
Hmmm... interesting. Nikcole's site shows the length of the top edge as 0.235" but because of the angle in the center of the body of the insert, it looks like max depth of cut would be half that. 17428

And both types of inserts appear to have the same length. So I'm still left wondering what the difference is between grooving and cut-off? Chin
Willie
Reply
Thanks given by:
#17
Nikcole's web site sucks. There really is very little information about their products on it and what is there is so small you can't read it. Smiley-gen163

Ed
Reply
Thanks given by:
#18
Sounds like a question for Ken.

I wonder if there is a radius on the edges of the groove inserts, so that you don't introduce a stress point by having a square edge. That wouldn't be necessary on the parting inserts. Also, you can get negative/positive parting tips, so that you leave the pip on the stock and not the part.

I'm probably totally wrong though!
Hunting American dentists since 2015.
Reply
Thanks given by:
#19
(02-13-2014, 01:23 PM)DaveH Wrote: Hi Willie,
According to http://www.mscdirect.com/browse/Indexabl...4287902322
Max depth of cut is 6mm (0.2362")
Smiley-eatdrink004
DaveH
I would have thought that if the insert was slightly wider than the holder the depth of cut would be greater than that.
What's the use of a parting off tool that can only part off from less than ½" dia. stock? 17428
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#20
(02-14-2014, 07:04 AM)EdK Wrote: Nikcole's web site sucks. There really is very little information about their products on it and what is there is so small you can't read it. Smiley-gen163

Ed

Ctrl - scroll wheel. Big Grin
Willie
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)