Shop Press
#51
(04-29-2013, 05:37 PM)TomG Wrote: Those are flame cut Ed, ya can't do that with cast iron. It looks like you got the new and improved model.

Tom

Thanks Tom. Now I'm not so worried about using them. One guy ended up with 8 stitches just to the right of his eye when one of the HF cast arbor plates exploded on him. His doctor told him he was lucky he didn't lose an eye it came that close.

Ed
Reply
Thanks given by:
#52
Agree with Tom. You should be good to go. If you wanted to test them, block up the ends and put a little pressure on the center. If they're cast, they'll crack easily. I don't mean so much that you bend them, but just enough to know they won't crack in two.

As always, safety glasses/shield wise during press work. You never know what's going to come flying out. It's pretty unnerving testing a newly built press. We built a rolling head straightening press at one shop I worked in. I designed it, and over calculated everything by a factor of 4, but even then, there was a bit of pucker as I watched the pressure gage go up to the 100 tons it was built for. Did fine though. Wish I had kept all my drawings. We used it to straighten some hollow mandrels up to about 8 feet long, so we sometimes (at first, anyway) ran a chain through the part in case it broke instead of bent. Never did have one break, so I suppose the heat treaters did the temper right.
Reply
Thanks given by:
#53
Like Tom said, you must have gotten the new improved model Ed.
I got the lumpy cast plates with my press, but again that was several years ago. I will only use them as doorstops or ballast weight.

I'm sure there is a lawyer somewhere that had something to do with the change.
Willie
Reply
Thanks given by:
#54
WAIT A MINUTE!!!


You buy a new press and all we get to see are two pictures of plates??? 17428
Reply
Thanks given by:
#55
(04-29-2013, 07:37 PM)Tony Wells Wrote: Agree with Tom. You should be good to go. If you wanted to test them, block up the ends and put a little pressure on the center. If they're cast, they'll crack easily. I don't mean so much that you bend them, but just enough to know they won't crack in two.

As always, safety glasses/shield wise during press work. You never know what's going to come flying out. It's pretty unnerving testing a newly built press....

A full face shield will definitely be worn when I use the press. Sweat

Ed
Reply
Thanks given by:
#56
(04-29-2013, 09:03 PM)wrustle Wrote: WAIT A MINUTE!!!


You buy a new press and all we get to see are two pictures of plates??? 17428

Ah, I'm having problems posting pictures. Yea, that's it.
Those are gorgeous arbor plates though, aren't they?

Ed

P.S. I'm taking pictures as I assemble it but last weekend was a full one and the 70 degree and sunny weather kept me out of the shop for the most part. I promise, pictures will be forthcoming, assuming I can get the picture posting problem solved. Blush
Reply
Thanks given by: wrustle
#57
Well this is embarrassing. It seems I somehow deleted the pictures I had taken while assembling the shop press. Not to worry though because I've decided to start over anyway. Laying in bed one night trying to get to sleep, I thought of a better way to assemble it so it ends up square. The assembly instructions just say to bolt this to that and this to that and you're done. You may be done but the thing is likely not going to be anywhere near square. I'll start over this coming weekend and be sure not to delete the pictures before I get them posted, that is if I can post them given the problems lately.

Ed
Reply
Thanks given by:
#58
(05-01-2013, 04:28 PM)EdK Wrote: Well this is embarrassing. It seems I somehow deleted the pictures I had taken while assembling the shop press. Not to worry though because I've decided to start over anyway. Laying in bed one night trying to get to sleep, I thought of a better way to assemble it so it ends up square. The assembly instructions just say to bolt this to that and this to that and you're done. You may be done but the thing is likely not going to be anywhere near square. I'll start over this coming weekend and be sure not to delete the pictures before I get them posted, that is if I can post them given the problems lately.

Ed

Ed.....it's only embarrassing cause you went and told us!!! Slaphead

RotflRotflRotfl
Reply
Thanks given by:
#59
(05-01-2013, 04:35 PM)wrustle Wrote:
(05-01-2013, 04:28 PM)EdK Wrote: Well this is embarrassing. It seems I somehow deleted the pictures I had taken while assembling the shop press. Not to worry though because I've decided to start over anyway. Laying in bed one night trying to get to sleep, I thought of a better way to assemble it so it ends up square. The assembly instructions just say to bolt this to that and this to that and you're done. You may be done but the thing is likely not going to be anywhere near square. I'll start over this coming weekend and be sure not to delete the pictures before I get them posted, that is if I can post them given the problems lately.

Ed

Ed.....it's only embarrassing cause you went and told us!!! Slaphead

RotflRotflRotfl

Yea, I can be pretty dumb at times, and this appears to be one of them. 5176 5176

Ed
Reply
Thanks given by:
#60
Lol, I thought I was the only one that did stuff like that.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)