MetalworkingFun Forum › Machining › General Metalworking Discussion v
Taps

Thread Modes
Taps
Bill Gruby
Unregistered
 
#32
12-27-2012, 05:05 PM
This is the first I have heard of Serial Taps also Dave. They are used to make a progressive thread cutting. #1 is a rougher followed by #2 an intermediate, followed by #3 the finish cut.

"Billy G"

http://www.carbidenz.co.nz/store/index.p...ct_id=1950
Reply
Thanks given by:


Messages In This Thread
Taps - by EdK - 10-03-2012, 06:08 AM
RE: Taps - by PixMan - 10-03-2012, 06:25 AM
RE: Taps - by EdK - 10-03-2012, 09:29 AM
RE: Taps - by wrustle - 10-03-2012, 03:41 PM
RE: Taps - by Arbalest - 10-03-2012, 06:30 AM
RE: Taps - by EdK - 10-03-2012, 09:20 AM
RE: Taps - by Mayhem - 10-03-2012, 06:30 AM
RE: Taps - by stevec - 10-03-2012, 07:20 AM
RE: Taps - by Mayhem - 10-03-2012, 07:36 AM
RE: Taps - by stevec - 10-03-2012, 07:49 AM
RE: Taps - by stevec - 10-03-2012, 09:40 AM
RE: Taps - by Arbalest - 10-03-2012, 09:59 AM
RE: Taps - by EdK - 10-03-2012, 05:50 PM
RE: Taps - by PixMan - 10-03-2012, 04:14 PM
RE: Taps - by sasquatch - 10-03-2012, 05:50 PM
RE: Taps - by stevec - 10-03-2012, 06:59 PM
RE: Taps - by Wawoodman - 10-04-2012, 08:38 AM
RE: Taps - by wrustle - 10-04-2012, 11:19 AM
RE: Taps - by TOM REED - 10-04-2012, 10:19 AM
RE: Taps - by EdK - 10-04-2012, 11:52 AM
RE: Taps - by Arbalest - 10-04-2012, 12:17 PM
RE: Taps - by EdK - 10-04-2012, 12:31 PM
RE: Taps - by Arbalest - 12-11-2012, 02:06 PM
RE: Taps - by stevec - 12-11-2012, 08:51 PM
RE: Taps - by sasquatch - 12-11-2012, 05:53 PM
RE: Taps - by sasquatch - 12-11-2012, 09:36 PM
RE: Taps - by Mayhem - 12-12-2012, 09:02 AM
RE: Taps - by DaveH - 12-12-2012, 06:35 PM
RE: Taps - by sasquatch - 12-12-2012, 09:29 PM
RE: Taps - by Arbalest - 12-27-2012, 01:09 PM
RE: Taps - by DaveH - 12-27-2012, 04:54 PM
RE: Taps - by Bill Gruby - 12-27-2012, 05:05 PM
RE: Taps - by Arbalest - 12-27-2012, 05:22 PM
RE: Taps - by DaveH - 12-27-2012, 05:55 PM
RE: Taps - by Arbalest - 12-27-2012, 07:41 PM
RE: Taps - by DaveH - 12-27-2012, 09:36 PM



Users browsing this thread: 1 Guest(s)