Setting stroke on Douglas Shaper

Hello There, Guest! Register

Thread Modes

Setting stroke on Douglas Shaper

dallen Offline

Offline

Senior

Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma

#22

09-24-2014, 05:35 PM

found this hiding in the furnace today, it measures 1.6 X 1.6 X 2.1 you think it will work, the material came from two shifter forks out of an old Kerney Trecker Horizontal Mill so it should be plenty tough.

I faced it off on the side the gate was on with a small 5 insert face mill.

DA

dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue

Tongue

Reply

Thanks given by: Shawn

« Next Oldest | Next Newest »

Messages In This Thread

Setting stroke on Douglas Shaper - by Shawn - 09-19-2014, 03:23 PM

RE: Setting stroke on Douglas Shaper - by dallen - 09-19-2014, 03:28 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-19-2014, 04:35 PM

RE: Setting stroke on Douglas Shaper - by f350ca - 09-19-2014, 04:42 PM

RE: Setting stroke on Douglas Shaper - by dallen - 09-19-2014, 06:57 PM

RE: Setting stroke on Douglas Shaper - by Mayhem - 09-19-2014, 11:30 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-20-2014, 01:00 AM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-20-2014, 01:05 AM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 01:18 AM

RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 08:59 AM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 02:05 PM

RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 02:50 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 04:14 PM

RE: Setting stroke on Douglas Shaper - by f350ca - 09-23-2014, 04:55 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 06:04 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 06:08 PM

RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 06:24 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 08:00 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 08:05 PM

RE: Setting stroke on Douglas Shaper - by f350ca - 09-23-2014, 09:08 PM

RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 09:23 PM

RE: Setting stroke on Douglas Shaper - by dallen - 09-24-2014, 05:35 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-24-2014, 07:30 PM

RE: Setting stroke on Douglas Shaper - by dallen - 09-24-2014, 09:18 PM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-25-2014, 01:20 AM

RE: Setting stroke on Douglas Shaper - by dallen - 09-25-2014, 07:34 AM

RE: Setting stroke on Douglas Shaper - by Shawn - 09-25-2014, 11:50 AM

Users browsing this thread: 3 Guest(s)