MetalworkingFun Forum › Machinery › Other Machinery › Shapers v
10.5" Douglas Shaper

Thread Modes
10.5" Douglas Shaper
Dave J Offline
Sophmore
***
Posts: 183
Threads: 22
Joined: Feb 2012
Location: Australia
#36
08-17-2013, 09:05 PM
Turn the square head cam bolt until it loose, then pull it out. You can then pull the head off and if it needs adjusting when you put it back together it has a fine thread to adjust it so the cam works just right.

Dave
Reply
Thanks given by: Mayhem


Messages In This Thread
10.5" Douglas Shaper - by Mayhem - 08-04-2013, 07:11 AM
RE: 10.5" Douglas Shaper - by dallen - 08-04-2013, 08:12 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-04-2013, 08:22 AM
RE: 10.5" Douglas Shaper - by EdK - 08-04-2013, 08:56 AM
RE: 10.5" Douglas Shaper - by dallen - 08-04-2013, 10:54 AM
RE: 10.5" Douglas Shaper - by sasquatch - 08-04-2013, 06:37 PM
RE: 10.5" Douglas Shaper - by Dave J - 08-04-2013, 10:26 PM
RE: 10.5" Douglas Shaper - by Mayhem - 08-05-2013, 02:42 AM
RE: 10.5" Douglas Shaper - by TomG - 08-05-2013, 11:08 AM
RE: 10.5" Douglas Shaper - by DaveH - 08-05-2013, 11:55 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-05-2013, 05:09 PM
RE: 10.5" Douglas Shaper - by dallen - 08-05-2013, 08:46 PM
RE: 10.5" Douglas Shaper - by Mayhem - 08-06-2013, 09:32 AM
RE: 10.5" Douglas Shaper - by dallen - 08-06-2013, 10:02 AM
RE: 10.5" Douglas Shaper - by Hawkeye - 08-06-2013, 11:17 PM
RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 12:26 AM
RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 12:43 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-07-2013, 05:34 AM
RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 05:43 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-10-2013, 08:33 AM
RE: 10.5" Douglas Shaper - by stevec - 08-10-2013, 12:38 PM
RE: 10.5" Douglas Shaper - by dallen - 08-10-2013, 12:47 PM
RE: 10.5" Douglas Shaper - by f350ca - 08-10-2013, 01:16 PM
RE: 10.5" Douglas Shaper - by dallen - 08-10-2013, 03:13 PM
RE: 10.5" Douglas Shaper - by Mayhem - 08-10-2013, 07:47 PM
RE: 10.5" Douglas Shaper - by Hawkeye - 08-10-2013, 08:13 PM
RE: 10.5" Douglas Shaper - by f350ca - 08-11-2013, 12:47 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-11-2013, 03:02 AM
RE: 10.5" Douglas Shaper - by f350ca - 08-11-2013, 08:56 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-11-2013, 09:02 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-15-2013, 07:01 AM
RE: 10.5" Douglas Shaper - by Dave J - 08-15-2013, 08:36 PM
RE: 10.5" Douglas Shaper - by castellated nut - 01-24-2019, 04:43 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-17-2013, 10:11 AM
RE: 10.5" Douglas Shaper - by dallen - 08-17-2013, 11:37 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-17-2013, 08:29 PM
RE: 10.5" Douglas Shaper - by Dave J - 08-17-2013, 09:05 PM
RE: 10.5" Douglas Shaper - by Mayhem - 09-03-2013, 08:27 AM
RE: 10.5" Douglas Shaper - by Mayhem - 09-03-2013, 08:31 AM
RE: 10.5" Douglas Shaper - by stevec - 09-03-2013, 11:30 AM
RE: 10.5" Douglas Shaper - by TomG - 01-24-2019, 10:02 AM
RE: 10.5" Douglas Shaper - by castellated nut - 01-24-2019, 05:28 PM



Users browsing this thread: 2 Guest(s)