MetalworkingFun Forum › Machining › General Metalworking Discussion v
How To Make A Flat Bottom Hole

Thread Modes
How To Make A Flat Bottom Hole
f350ca Offline
Senior
*****
Posts: 3,002
Threads: 51
Joined: Apr 2012
Location: Ontario
#9
12-13-2012, 10:12 AM
I wouldn't hesitate to do that with an end mill. Two flute if it was a blind hole, but you can drill through with the 0.17 then ream with a 2 or 4 flute. Can't see that coming out of the vice.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 08:23 AM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-13-2012, 08:26 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:19 AM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:39 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:05 PM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 08:46 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 09:31 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by f350ca - 12-13-2012, 10:12 AM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 11:33 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 12:19 PM
RE: How To Make A Flat Bottom Hole - by Arbalest - 12-13-2012, 01:07 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 01:10 PM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:41 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:07 PM
RE: How To Make A Flat Bottom Hole - by DaveH - 12-13-2012, 01:22 PM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 01:59 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-13-2012, 05:52 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:10 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 05:00 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-14-2012, 05:29 PM
RE: How To Make A Flat Bottom Hole - by Mayhem - 12-13-2012, 10:07 PM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-13-2012, 10:59 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 06:55 AM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-14-2012, 07:50 AM
RE: How To Make A Flat Bottom Hole - by petertha - 12-14-2012, 03:35 PM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-14-2012, 05:20 PM



Users browsing this thread: 1 Guest(s)