MetalworkingFun Forum › Machining › General Metalworking Discussion v
Boring heads for the mill

Thread Modes
Boring heads for the mill
pineyfolks
Unregistered
 
#32
07-25-2012, 04:20 AM
A simple bar with a tool that can be slid in and out and set with a micrometer will get you by for one time jobs. Make several, setup on a scrap piece and write the bore sizes on them, put them in your toolbox for next time or change them as needed.
Reply
Thanks given by:


Messages In This Thread
Boring heads for the mill - by DanH - 06-04-2012, 01:32 PM
RE: Boring heads for the mill - by doubleboost - 06-04-2012, 02:12 PM
RE: Boring heads for the mill - by Hopefuldave - 06-04-2012, 02:22 PM
RE: Boring heads for the mill - by DanH - 06-04-2012, 03:43 PM
RE: Boring heads for the mill - by EdK - 06-04-2012, 04:16 PM
RE: Boring heads for the mill - by f350ca - 06-04-2012, 05:23 PM
RE: Boring heads for the mill - by DaveH - 06-04-2012, 05:26 PM
RE: Boring heads for the mill - by EdK - 06-04-2012, 05:39 PM
RE: Boring heads for the mill - by DanH - 06-04-2012, 08:06 PM
RE: Boring heads for the mill - by ukazak - 06-05-2012, 01:45 AM
RE: Boring heads for the mill - by doubleboost - 06-05-2012, 05:10 AM
RE: Boring heads for the mill - by Mayhem - 06-05-2012, 06:24 AM
RE: Boring heads for the mill - by f350ca - 06-05-2012, 09:57 AM
RE: Boring heads for the mill - by Highpower - 06-05-2012, 03:45 PM
RE: Boring heads for the mill - by EdK - 06-05-2012, 03:59 PM
RE: Boring heads for the mill - by rleete - 06-05-2012, 06:56 PM
RE: Boring heads for the mill - by stevec - 06-05-2012, 07:18 PM
RE: Boring heads for the mill - by DanH - 06-05-2012, 07:28 PM
RE: Boring heads for the mill - by krv3000 - 06-06-2012, 05:05 AM
RE: Boring heads for the mill - by PixMan - 06-15-2012, 10:09 PM
RE: Boring heads for the mill - by TomG - 06-21-2012, 12:35 PM
RE: Boring heads for the mill - by DaveH - 06-21-2012, 01:43 PM
RE: Boring heads for the mill - by TomG - 06-21-2012, 02:21 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 02:45 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 01:56 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 03:02 PM
RE: Boring heads for the mill - by Keith_W - 06-22-2012, 03:33 PM
RE: Boring heads for the mill - by TomG - 06-22-2012, 05:34 PM
RE: Boring heads for the mill - by DaveH - 06-23-2012, 07:15 AM
RE: Boring heads for the mill - by PixMan - 06-22-2012, 07:10 PM
RE: Boring heads for the mill - by EdK - 06-22-2012, 07:16 PM
RE: Boring heads for the mill - by pineyfolks - 07-25-2012, 04:20 AM



Users browsing this thread: 2 Guest(s)