MetalworkingFun Forum › Machining › General Metalworking Discussion v
Help with drawing

Thread Modes
Help with drawing
EdK Online
Whipping Boy
*******
Posts: 8,748
Threads: 314
Joined: Feb 2012
Location: Arizona/Minnesota
#31
05-05-2012, 01:02 PM
(05-05-2012, 11:30 AM)Turbinedoctor Wrote: No problem Ed. I was just wondering if it was done automaticly.

I dont have Adobe Pro on my computer yet but it's coming.

If you have Microsoft Word you can save the file as a PDF file rather than a .docx file.

Ed
Reply
Thanks given by:


Messages In This Thread
Help with drawing - by Turbinedoctor - 04-19-2012, 04:30 AM
RE: Help with drawing - by stevec - 04-19-2012, 07:24 AM
RE: Help with drawing - by EdK - 04-19-2012, 05:26 PM
RE: Help with drawing - by Hopefuldave - 04-19-2012, 05:53 PM
RE: Help with drawing - by EdK - 04-19-2012, 06:39 PM
RE: Help with drawing - by Tony Wells - 04-19-2012, 07:08 PM
RE: Help with drawing - by PixMan - 04-19-2012, 08:27 PM
RE: Help with drawing - by Tony Wells - 04-19-2012, 08:41 PM
RE: Help with drawing - by DanH - 04-19-2012, 11:22 PM
RE: Help with drawing - by Turbinedoctor - 04-19-2012, 11:39 PM
RE: Help with drawing - by Tony Wells - 04-20-2012, 12:27 AM
RE: Help with drawing - by Turbinedoctor - 04-20-2012, 03:00 AM
RE: Help with drawing - by claudef - 04-20-2012, 07:18 AM
RE: Help with drawing - by Tony Wells - 04-20-2012, 08:47 AM
RE: Help with drawing - by Highpower - 04-20-2012, 10:21 AM
RE: Help with drawing - by stevec - 04-20-2012, 06:46 PM
RE: Help with drawing - by EdK - 04-20-2012, 06:52 PM
RE: Help with drawing - by Highpower - 04-20-2012, 08:05 PM
RE: Help with drawing - by EdK - 04-20-2012, 08:10 PM
RE: Help with drawing - by Turbinedoctor - 04-21-2012, 06:53 PM
RE: Help with drawing - by Tony Wells - 04-21-2012, 07:12 PM
RE: Help with drawing - by Turbinedoctor - 04-21-2012, 09:30 PM
RE: Help with drawing - by Turbinedoctor - 05-03-2012, 07:25 PM
RE: Help with drawing - by EdK - 05-03-2012, 07:42 PM
RE: Help with drawing - by DaveH - 05-03-2012, 07:49 PM
RE: Help with drawing - by Turbinedoctor - 05-03-2012, 08:36 PM
RE: Help with drawing - by EdK - 05-04-2012, 06:15 AM
RE: Help with drawing - by Turbinedoctor - 05-03-2012, 08:38 PM
RE: Help with drawing - by Tony Wells - 05-04-2012, 12:32 PM
RE: Help with drawing - by Turbinedoctor - 05-05-2012, 11:30 AM
RE: Help with drawing - by EdK - 05-05-2012, 01:02 PM



Users browsing this thread: 1 Guest(s)