MetalworkingFun Forum › Machining › General Metalworking Discussion v
How To Make A Flat Bottom Hole

Thread Modes
How To Make A Flat Bottom Hole
EdK Offline
Whipping Boy
*******
Posts: 8,749
Threads: 314
Joined: Feb 2012
Location: Arizona/Minnesota
#6
12-13-2012, 09:23 AM
(12-13-2012, 08:46 AM)dallen Wrote: endmill

I'd be concerned that the end mill would grab the part and tear it out of the vise. The material is aluminum which gets kind of grumpy when trying to do a plunge cut like that. I'd probably end up snapping off the 1/4" end mill and not only ruin the end mill but the part and my day.

Ed
Reply
Thanks given by:


Messages In This Thread
How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 08:23 AM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-13-2012, 08:26 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:19 AM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:39 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:05 PM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 08:46 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 09:31 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by f350ca - 12-13-2012, 10:12 AM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 11:33 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 12:19 PM
RE: How To Make A Flat Bottom Hole - by Arbalest - 12-13-2012, 01:07 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 01:10 PM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:41 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:07 PM
RE: How To Make A Flat Bottom Hole - by DaveH - 12-13-2012, 01:22 PM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 01:59 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-13-2012, 05:52 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:10 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 05:00 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-14-2012, 05:29 PM
RE: How To Make A Flat Bottom Hole - by Mayhem - 12-13-2012, 10:07 PM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-13-2012, 10:59 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 06:55 AM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-14-2012, 07:50 AM
RE: How To Make A Flat Bottom Hole - by petertha - 12-14-2012, 03:35 PM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-14-2012, 05:20 PM



Users browsing this thread: 1 Guest(s)