|
milling in the lathe
|
08-23-2012, 03:33 PM
The biggest thing I want to use it for is making slots in DOM tubing, finishing 80% AR lower receivers and possibly turning a bolt head. Other than that everything else is really small and I will just have to get used to looking at what I want laying on it's side rather than looking down at it.
SnailPowered, proud to be a member of MetalworkingFun since Aug 2012.
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
milling in the lathe - by krv3000 - 03-04-2012, 10:18 AM
RE: milling in the lathe - by DaveH - 03-04-2012, 10:22 AM
RE: milling in the lathe - by krv3000 - 03-13-2012, 05:23 PM
RE: milling in the lathe - by DaveH - 03-14-2012, 12:35 PM
RE: milling in the lathe - by ETC57 - 03-14-2012, 04:49 PM
RE: milling in the lathe - by doubleboost - 03-14-2012, 05:02 PM
RE: milling in the lathe - by ETC57 - 03-14-2012, 10:34 PM
RE: milling in the lathe - by DaveH - 03-14-2012, 05:26 PM
RE: milling in the lathe - by krv3000 - 03-14-2012, 05:42 PM
RE: milling in the lathe - by ETC57 - 03-14-2012, 10:44 PM
RE: milling in the lathe - by krv3000 - 03-15-2012, 02:07 PM
RE: milling in the lathe - by aametalmaster - 03-19-2012, 08:17 PM
RE: milling in the lathe - by aametalmaster - 03-19-2012, 08:18 PM
RE: milling in the lathe - by krv3000 - 03-20-2012, 02:41 AM
RE: milling in the lathe - by EdK - 03-20-2012, 06:29 AM
RE: milling in the lathe - by DaveH - 03-20-2012, 06:34 AM
RE: milling in the lathe - by ETC57 - 03-20-2012, 02:52 PM
RE: milling in the lathe - by aametalmaster - 03-20-2012, 04:56 PM
RE: milling in the lathe - by doubleboost - 03-20-2012, 05:04 PM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 12:48 AM
RE: milling in the lathe - by EdK - 08-23-2012, 05:21 AM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 03:36 PM
RE: milling in the lathe - by EdK - 08-23-2012, 03:40 PM
RE: milling in the lathe - by f350ca - 08-23-2012, 08:31 AM
RE: milling in the lathe - by DaveH - 08-23-2012, 08:38 AM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 01:36 PM
RE: milling in the lathe - by DaveH - 08-23-2012, 02:22 PM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 03:33 PM
RE: milling in the lathe - by aametalmaster - 08-23-2012, 06:31 PM
RE: milling in the lathe - by stevec - 08-23-2012, 06:45 PM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 11:16 PM
RE: milling in the lathe - by Rickabilly - 09-17-2012, 07:10 AM
|
