MetalworkingFun Forum › Machinery › Other Machinery › Shapers v
Shaper toolholders

Thread Modes
Shaper toolholders
Sunset Machine Offline
Junior
****
Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA
#28
08-22-2012, 08:34 AM
One thing puzzles me: if we use side rake, why is there a reverse feed? For that matter, which direction is preferred? Do we finish with the same tool? My thinking was to use the still-sharp opposite side for finishing, hence no side rake.
Reply
Thanks given by:


Messages In This Thread
Shaper toolholders - by Sunset Machine - 08-12-2012, 09:38 AM
RE: Shaper toolholders - by Mayhem - 08-12-2012, 09:52 AM
RE: Shaper toolholders - by Sunset Machine - 08-12-2012, 10:00 AM
RE: Shaper toolholders - by dallen - 08-12-2012, 11:06 AM
RE: Shaper toolholders - by f350ca - 08-12-2012, 11:37 AM
RE: Shaper toolholders - by dallen - 08-12-2012, 02:02 PM
RE: Shaper toolholders - by f350ca - 08-12-2012, 06:18 PM
RE: Shaper toolholders - by big job - 08-13-2012, 05:32 AM
RE: Shaper toolholders - by TomG - 08-13-2012, 07:02 AM
RE: Shaper toolholders - by Rickabilly - 08-20-2012, 03:53 PM
RE: Shaper toolholders - by Sunset Machine - 08-13-2012, 07:54 AM
RE: Shaper toolholders - by marduk - 08-17-2012, 03:19 AM
RE: Shaper toolholders - by DaveH - 08-17-2012, 07:44 AM
RE: Shaper toolholders - by ScrapMetal - 08-17-2012, 04:08 PM
RE: Shaper toolholders - by marduk - 08-17-2012, 04:45 PM
RE: Shaper toolholders - by stevec - 08-17-2012, 04:56 PM
RE: Shaper toolholders - by marduk - 08-17-2012, 05:00 PM
RE: Shaper toolholders - by DaveH - 08-17-2012, 05:04 PM
RE: Shaper toolholders - by TomG - 08-20-2012, 06:25 PM
RE: Shaper toolholders - by stevec - 08-20-2012, 06:30 PM
RE: Shaper toolholders - by f350ca - 08-20-2012, 07:47 PM
RE: Shaper toolholders - by Rickabilly - 08-21-2012, 02:29 AM
RE: Shaper toolholders - by stevec - 08-21-2012, 07:03 AM
RE: Shaper toolholders - by Sunset Machine - 08-21-2012, 07:58 AM
RE: Shaper toolholders - by Rickabilly - 08-21-2012, 04:50 PM
RE: Shaper toolholders - by Rickabilly - 08-21-2012, 05:18 PM
RE: Shaper toolholders - by dallen - 08-21-2012, 04:14 PM
RE: Shaper toolholders - by Sunset Machine - 08-22-2012, 08:34 AM
RE: Shaper toolholders - by Rickabilly - 08-22-2012, 08:51 AM
RE: Shaper toolholders - by stevec - 08-22-2012, 10:40 AM
RE: Shaper toolholders - by Rickabilly - 08-22-2012, 03:26 PM
RE: Shaper toolholders - by Sunset Machine - 08-22-2012, 07:30 PM
RE: Shaper toolholders - by Rickabilly - 08-23-2012, 07:01 AM



Users browsing this thread: 5 Guest(s)