|
Great Tool Post
|
08-22-2012, 07:16 AM
(08-22-2012, 07:01 AM)stevec Wrote: As regards trig or cad (neither of which I'm familiar with) I'm gonna need to read up on the roller to roller measurement procedure. Steve, Dowel pins are typically what are used. 1/4" or 3/8" would be good sizes for what you're going to be doing. I did it in CAD yesterday for a project. Ed |
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Great Tool Post - by claudef - 08-20-2012, 06:44 PM
RE: Great Tool Post - by ferryman - 08-20-2012, 07:55 PM
RE: Great Tool Post - by claudef - 08-21-2012, 06:25 AM
RE: Great Tool Post - by EdK - 08-21-2012, 05:52 AM
RE: Great Tool Post - by claudef - 08-21-2012, 06:13 AM
RE: Great Tool Post - by DaveH - 08-21-2012, 06:03 AM
RE: Great Tool Post - by stevec - 08-21-2012, 06:51 AM
RE: Great Tool Post - by claudef - 08-21-2012, 07:54 AM
RE: Great Tool Post - by stevec - 08-22-2012, 07:01 AM
RE: Great Tool Post - by EdK - 08-22-2012, 07:16 AM
RE: Great Tool Post - by PixMan - 08-21-2012, 07:25 AM
RE: Great Tool Post - by stevec - 08-22-2012, 06:39 AM
RE: Great Tool Post - by doubleboost - 08-21-2012, 03:52 PM
RE: Great Tool Post - by claudef - 08-23-2012, 03:42 PM
RE: Great Tool Post - by sasquatch - 08-21-2012, 06:32 PM
RE: Great Tool Post - by starlight_tools - 08-21-2012, 07:29 PM
RE: Great Tool Post - by SnailPowered - 08-21-2012, 10:01 PM
RE: Great Tool Post - by EdK - 08-22-2012, 05:27 AM
RE: Great Tool Post - by stevec - 08-22-2012, 06:31 AM
RE: Great Tool Post - by SnailPowered - 08-22-2012, 06:24 AM
RE: Great Tool Post - by Mayhem - 08-22-2012, 06:37 AM
RE: Great Tool Post - by Mayhem - 08-22-2012, 07:29 AM
RE: Great Tool Post - by DanH - 08-22-2012, 09:34 AM
RE: Great Tool Post - by stevec - 08-22-2012, 10:20 AM
RE: Great Tool Post - by f350ca - 08-22-2012, 02:51 PM
RE: Great Tool Post - by stevec - 08-22-2012, 07:53 PM
RE: Great Tool Post - by stevec - 08-23-2012, 06:32 PM
RE: Great Tool Post - by Mayhem - 08-23-2012, 09:03 PM
RE: Great Tool Post - by EdK - 08-23-2012, 09:16 PM
RE: Great Tool Post - by stevec - 08-24-2012, 07:00 AM
RE: Great Tool Post - by SnailPowered - 08-24-2012, 07:40 AM
RE: Great Tool Post - by Highpower - 08-24-2012, 02:26 PM
RE: Great Tool Post - by stevec - 08-24-2012, 04:18 PM
RE: Great Tool Post - by Highpower - 08-24-2012, 05:53 PM
RE: Great Tool Post - by PixMan - 08-25-2012, 09:33 PM
RE: Great Tool Post - by stevec - 08-26-2012, 07:11 AM
RE: Great Tool Post - by PixMan - 08-26-2012, 07:57 AM
RE: Great Tool Post - by stevec - 08-26-2012, 08:57 AM
RE: Great Tool Post - by Mayhem - 08-26-2012, 06:49 PM
|
