Expectations of a granite surface plate ...

Hello There, Guest! Register

Thread Modes

Expectations of a granite surface plate ...

ETC57

Offline

Junior

Posts: 576
Threads: 18
Joined: Feb 2012
Location: Washington State USA

#19

03-06-2012, 05:19 PM (This post was last modified: 03-06-2012, 05:20 PM by ETC57.)

Steve,
to answer your question from my experience some of the plates I have installed have been finished on both sides

Jerry. Popcorn

Popcorn

ETC57, proud to be a member of MetalworkingFun Forum since Feb 2012.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Expectations of a granite surface plate ... - by arvidj - 03-06-2012, 01:13 PM

RE: Expectations of a granite surface plate ... - by EdK - 03-06-2012, 01:21 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 02:12 PM

RE: Expectations of a granite surface plate ... - by DaveH - 03-06-2012, 02:21 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 02:35 PM

RE: Expectations of a granite surface plate ... - by DaveH - 03-06-2012, 02:49 PM

RE: Expectations of a granite surface plate ... - by arvidj - 03-06-2012, 03:44 PM

RE: Expectations of a granite surface plate ... - by DaveH - 03-06-2012, 03:51 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 03:55 PM

RE: Expectations of a granite surface plate ... - by arvidj - 03-06-2012, 04:32 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 03:48 PM

RE: Expectations of a granite surface plate ... - by DaveH - 03-06-2012, 03:56 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 04:07 PM

RE: Expectations of a granite surface plate ... - by doubleboost - 03-06-2012, 04:50 PM

RE: Expectations of a granite surface plate ... - by DaveH - 03-06-2012, 04:53 PM

RE: Expectations of a granite surface plate ... - by doubleboost - 03-06-2012, 04:56 PM

RE: Expectations of a granite surface plate ... - by DaveH - 03-06-2012, 05:04 PM

RE: Expectations of a granite surface plate ... - by stevec - 03-06-2012, 05:12 PM

RE: Expectations of a granite surface plate ... - by DaveH - 03-06-2012, 05:28 PM

RE: Expectations of a granite surface plate ... - by arvidj - 03-06-2012, 07:34 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 05:19 PM

RE: Expectations of a granite surface plate ... - by doubleboost - 03-06-2012, 05:27 PM

RE: Expectations of a granite surface plate ... - by EdK - 03-06-2012, 06:12 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 06:49 PM

RE: Expectations of a granite surface plate ... - by Mayhem - 03-06-2012, 07:58 PM

RE: Expectations of a granite surface plate ... - by Tony Wells - 03-06-2012, 11:25 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 11:36 PM

RE: Expectations of a granite surface plate ... - by Tony Wells - 03-06-2012, 11:40 PM

RE: Expectations of a granite surface plate ... - by ETC57 - 03-06-2012, 11:49 PM

RE: Expectations of a granite surface plate ... - by EdK - 03-07-2012, 01:28 PM

Users browsing this thread: 10 Guest(s)