MetalworkingFun Forum › Machining › Welding & Casting v
Mill Engine Cylinder Casting

Thread Modes
Mill Engine Cylinder Casting
SnailPowered Offline
Junior
****
Posts: 258
Threads: 13
Joined: Aug 2012
Location: USA
#24
08-21-2012, 10:49 AM (This post was last modified: 08-21-2012, 10:50 AM by SnailPowered.)
(08-21-2012, 07:19 AM)Mayhem Wrote:
(08-20-2012, 06:11 PM)TomG Wrote: More displacement equals more torque. Thumbsup

Tom

Or as the saying goes, "there is no substitute for cubic inches"

BAH Humbug! Rotfl Boost is definitely a replacement for displacement. Look at the new Ford Eco-boost. I'm not a Ford fan at all but I WANT that truck!! Thumbsup
SnailPowered, proud to be a member of MetalworkingFun since Aug 2012.
Reply
Thanks given by:


Messages In This Thread
Mill Engine Cylinder Casting - by doubleboost - 08-12-2012, 02:49 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-12-2012, 03:48 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-12-2012, 03:51 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-12-2012, 04:10 PM
RE: Mill Engine Cylinder Casting - by Mayhem - 08-12-2012, 11:45 PM
RE: Mill Engine Cylinder Casting - by krv3000 - 08-13-2012, 01:48 AM
RE: Mill Engine Cylinder Casting - by Highpower - 08-13-2012, 07:16 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 10:54 AM
RE: Mill Engine Cylinder Casting - by Highpower - 08-13-2012, 03:59 PM
RE: Mill Engine Cylinder Casting - by TomG - 08-13-2012, 07:19 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 04:03 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 04:38 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-13-2012, 04:45 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-14-2012, 03:45 PM
RE: Mill Engine Cylinder Casting - by EdK - 08-14-2012, 04:09 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-14-2012, 04:21 PM
RE: Mill Engine Cylinder Casting - by ETC57 - 08-14-2012, 09:17 PM
RE: Mill Engine Cylinder Casting - by f350ca - 08-14-2012, 09:26 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-20-2012, 04:57 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-20-2012, 05:15 PM
RE: Mill Engine Cylinder Casting - by TomG - 08-20-2012, 06:11 PM
RE: Mill Engine Cylinder Casting - by Mayhem - 08-21-2012, 07:19 AM
RE: Mill Engine Cylinder Casting - by SnailPowered - 08-21-2012, 10:49 AM
RE: Mill Engine Cylinder Casting - by TomG - 08-21-2012, 01:15 PM
RE: Mill Engine Cylinder Casting - by dallen - 09-15-2012, 08:18 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 09-15-2012, 11:17 AM
RE: Mill Engine Cylinder Casting - by DaveH - 09-15-2012, 01:04 PM
RE: Mill Engine Cylinder Casting - by dallen - 09-15-2012, 01:18 PM



Users browsing this thread: 3 Guest(s)