Hello everyone here, a tool that I make for my filer metals it goes very well and it is not very hard was realized, the corp is made from pieces of a steel section 40x20mm, and head is realize in a sketch of 60mm diameter, all being welded then the parts as remanufactured, I attached video of the whole, well ordialement thierry http://youtu.be/BR7TfL-zMZA
|
Shaper toolholders
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Shaper toolholders - by Sunset Machine - 08-12-2012, 09:38 AM
RE: Shaper toolholders - by Mayhem - 08-12-2012, 09:52 AM
RE: Shaper toolholders - by Sunset Machine - 08-12-2012, 10:00 AM
RE: Shaper toolholders - by dallen - 08-12-2012, 11:06 AM
RE: Shaper toolholders - by f350ca - 08-12-2012, 11:37 AM
RE: Shaper toolholders - by dallen - 08-12-2012, 02:02 PM
RE: Shaper toolholders - by f350ca - 08-12-2012, 06:18 PM
RE: Shaper toolholders - by big job - 08-13-2012, 05:32 AM
RE: Shaper toolholders - by TomG - 08-13-2012, 07:02 AM
RE: Shaper toolholders - by Rickabilly - 08-20-2012, 03:53 PM
RE: Shaper toolholders - by Sunset Machine - 08-13-2012, 07:54 AM
RE: Shaper toolholders - by marduk - 08-17-2012, 03:19 AM
RE: Shaper toolholders - by DaveH - 08-17-2012, 07:44 AM
RE: Shaper toolholders - by ScrapMetal - 08-17-2012, 04:08 PM
RE: Shaper toolholders - by marduk - 08-17-2012, 04:45 PM
RE: Shaper toolholders - by stevec - 08-17-2012, 04:56 PM
RE: Shaper toolholders - by marduk - 08-17-2012, 05:00 PM
RE: Shaper toolholders - by DaveH - 08-17-2012, 05:04 PM
RE: Shaper toolholders - by TomG - 08-20-2012, 06:25 PM
RE: Shaper toolholders - by stevec - 08-20-2012, 06:30 PM
RE: Shaper toolholders - by f350ca - 08-20-2012, 07:47 PM
RE: Shaper toolholders - by Rickabilly - 08-21-2012, 02:29 AM
RE: Shaper toolholders - by stevec - 08-21-2012, 07:03 AM
RE: Shaper toolholders - by Sunset Machine - 08-21-2012, 07:58 AM
RE: Shaper toolholders - by Rickabilly - 08-21-2012, 04:50 PM
RE: Shaper toolholders - by Rickabilly - 08-21-2012, 05:18 PM
RE: Shaper toolholders - by dallen - 08-21-2012, 04:14 PM
RE: Shaper toolholders - by Sunset Machine - 08-22-2012, 08:34 AM
RE: Shaper toolholders - by Rickabilly - 08-22-2012, 08:51 AM
RE: Shaper toolholders - by stevec - 08-22-2012, 10:40 AM
RE: Shaper toolholders - by Rickabilly - 08-22-2012, 03:26 PM
RE: Shaper toolholders - by Sunset Machine - 08-22-2012, 07:30 PM
RE: Shaper toolholders - by Rickabilly - 08-23-2012, 07:01 AM
|
Users browsing this thread: 1 Guest(s)