Single point threading problem

Thread Modes

Single point threading problem

Mayhem Offline

purveyor of mischief

Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia

07-30-2012, 07:52 AM

Thanks Tony. The major diameter is 4", so using the calculator you linked to the helix angle is 0.7598.

Thanks DA. I'll check to see if it is rubbing. From what I understood the top was best left flat but I'mm willing to put some relief on the top.

Hunting American dentists since 2015.

Like Post

« Next Oldest | Next Newest »

Messages In This Thread

Single point threading problem - by Mayhem - 07-30-2012, 05:57 AM

RE: Single point threading problem - by Highpower - 07-30-2012, 06:30 AM

RE: Single point threading problem - by Mayhem - 07-30-2012, 06:33 AM

RE: Single point threading problem - by Highpower - 07-30-2012, 06:36 AM

RE: Single point threading problem - by stevec - 07-30-2012, 06:54 AM

RE: Single point threading problem - by Tony Wells - 07-30-2012, 07:33 AM

RE: Single point threading problem - by dallen - 07-30-2012, 07:42 AM

RE: Single point threading problem - by Mayhem - 07-30-2012, 07:52 AM

RE: Single point threading problem - by Sunset Machine - 07-30-2012, 09:09 AM

RE: Single point threading problem - by stevec - 07-30-2012, 01:40 PM

RE: Single point threading problem - by Hopefuldave - 07-30-2012, 03:51 PM

RE: Single point threading problem - by Sunset Machine - 07-30-2012, 06:25 PM

RE: Single point threading problem - by Tony Wells - 07-30-2012, 07:16 PM

RE: Single point threading problem - by Sunset Machine - 07-31-2012, 08:11 AM

RE: Single point threading problem - by Tony Wells - 07-31-2012, 10:24 AM

RE: Single point threading problem - by Mayhem - 09-01-2012, 10:44 PM

RE: Single point threading problem - by f350ca - 09-02-2012, 12:20 AM

RE: Single point threading problem - by Hopefuldave - 09-02-2012, 01:11 PM

RE: Single point threading problem - by Mayhem - 09-02-2012, 12:25 AM

RE: Single point threading problem - by big job - 09-02-2012, 05:31 AM

RE: Single point threading problem - by Mayhem - 09-02-2012, 05:37 AM

RE: Single point threading problem - by stevec - 09-02-2012, 07:26 AM

RE: Single point threading problem - by dallen - 09-02-2012, 07:48 AM

RE: Single point threading problem - by Sunset Machine - 09-02-2012, 09:30 AM

RE: Single point threading problem - by Mayhem - 08-05-2014, 07:01 AM

RE: Single point threading problem - by DaveH - 08-05-2014, 07:08 AM

RE: Single point threading problem - by Mayhem - 08-05-2014, 07:12 AM

RE: Single point threading problem - by stevec - 08-05-2014, 07:27 AM

RE: Single point threading problem - by awemawson - 08-05-2014, 07:31 AM

RE: Single point threading problem - by DaveH - 08-05-2014, 10:03 AM

RE: Single point threading problem - by EdK - 08-05-2014, 11:42 AM

RE: Single point threading problem - by EdK - 08-05-2014, 11:46 AM

RE: Single point threading problem - by stevec - 08-05-2014, 02:33 PM

RE: Single point threading problem - by f350ca - 08-05-2014, 04:55 PM

RE: Single point threading problem - by stevec - 08-05-2014, 05:59 PM

Users browsing this thread: 2 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me