mini mill

Thread Modes

mini mill

dallen Offline

Senior

Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma

#20

07-13-2012, 11:01 PM (This post was last modified: 07-14-2012, 08:04 AM by dallen.)

(07-12-2012, 10:46 PM)ETC57 Wrote: Thanks Dallen,

Is there a special blade for that? Or just what's handy.

Jerry.

here is a photo of the scrapper I made yesterday, I silver soldered a bit of carbide onto a short length of 1/8 by half inch wide flat bar, today I added the handle.

this is the photo of the gib that goes in the column slide, sorry I didn't take a picture of it before I started working on it.

dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue

Like Post

« Next Oldest | Next Newest »

Messages In This Thread

mini mill - by dallen - 07-07-2012, 10:50 PM

RE: mini mill - by Highpower - 07-08-2012, 07:33 AM

RE: mini mill - by DaveH - 07-08-2012, 11:12 AM

RE: mini mill - by ETC57 - 07-08-2012, 11:20 AM

RE: mini mill - by henryarnold - 07-08-2012, 12:23 PM

RE: mini mill - by dallen - 07-08-2012, 01:20 PM

RE: mini mill - by Mayhem - 07-09-2012, 04:28 AM

RE: mini mill - by dallen - 07-09-2012, 11:40 AM

RE: mini mill - by dallen - 07-11-2012, 09:15 PM

RE: mini mill - by dallen - 07-12-2012, 01:19 AM

RE: mini mill - by DaveH - 07-12-2012, 08:31 AM

RE: mini mill - by dallen - 07-12-2012, 05:28 PM

RE: mini mill - by ETC57 - 07-12-2012, 06:23 PM

RE: mini mill - by dallen - 07-12-2012, 10:20 PM

RE: mini mill - by Mayhem - 07-12-2012, 08:17 PM

RE: mini mill - by dallen - 07-12-2012, 10:12 PM

RE: mini mill - by ETC57 - 07-12-2012, 10:46 PM

RE: mini mill - by dallen - 07-13-2012, 11:01 PM

RE: mini mill - by dallen - 07-12-2012, 10:57 PM

RE: mini mill - by dallen - 07-13-2012, 07:51 AM

RE: mini mill - by DaveH - 07-14-2012, 06:03 AM

RE: mini mill - by dallen - 07-14-2012, 09:11 PM

RE: mini mill - by DaveH - 07-15-2012, 06:28 AM

RE: mini mill - by dallen - 07-15-2012, 07:27 AM

RE: mini mill - by Rickabilly - 07-16-2012, 09:12 PM

RE: mini mill - by dallen - 07-17-2012, 07:12 AM

RE: mini mill - by Rickabilly - 07-17-2012, 08:55 AM

RE: mini mill - by Highpower - 07-17-2012, 09:34 AM

RE: mini mill - by dallen - 07-17-2012, 12:23 PM

RE: mini mill - by DaveH - 07-17-2012, 02:12 PM

RE: mini mill - by Rickabilly - 07-17-2012, 10:53 PM

RE: mini mill - by Mayhem - 07-18-2012, 06:32 AM

RE: mini mill - by Rickabilly - 07-18-2012, 07:20 AM

RE: mini mill - by Mayhem - 07-18-2012, 07:33 AM

RE: mini mill - by dallen - 07-20-2012, 07:23 AM

RE: mini mill - by Rickabilly - 07-21-2012, 02:53 AM

RE: mini mill - by Rickabilly - 07-21-2012, 09:19 AM

RE: mini mill - by Mayhem - 07-21-2012, 09:55 AM

RE: mini mill - by dallen - 07-21-2012, 11:32 AM

RE: mini mill - by Rickabilly - 07-22-2012, 06:48 AM

RE: mini mill - by dallen - 07-22-2012, 08:43 AM

RE: mini mill - by NevadaBlue - 07-22-2012, 07:19 PM

RE: mini mill - by DaveH - 07-22-2012, 07:28 PM

RE: mini mill - by NevadaBlue - 07-22-2012, 07:37 PM

RE: mini mill - by EdK - 07-23-2012, 05:29 AM

RE: mini mill - by dallen - 07-22-2012, 08:49 PM

RE: mini mill - by NevadaBlue - 07-23-2012, 12:39 AM

RE: mini mill - by dallen - 07-23-2012, 07:07 AM

RE: mini mill - by Rickabilly - 07-23-2012, 02:12 PM

RE: mini mill - by EdK - 07-23-2012, 03:47 PM

RE: mini mill - by NevadaBlue - 07-24-2012, 07:00 PM

RE: mini mill - by Mayhem - 07-24-2012, 07:17 PM

RE: mini mill - by Highpower - 07-25-2012, 09:26 AM

RE: mini mill - by dallen - 07-25-2012, 10:16 AM

RE: mini mill - by Highpower - 07-25-2012, 10:37 AM

RE: mini mill - by dallen - 07-25-2012, 11:39 AM

RE: mini mill - by Rickabilly - 07-25-2012, 02:35 PM

RE: mini mill - by Highpower - 07-25-2012, 04:09 PM

RE: mini mill - by EdK - 07-25-2012, 04:18 PM

RE: mini mill - by dallen - 07-25-2012, 04:21 PM

RE: mini mill - by Mayhem - 07-26-2012, 05:02 AM

RE: mini mill - by Rickabilly - 07-27-2012, 03:21 AM

RE: mini mill - by Mayhem - 07-27-2012, 12:30 AM

RE: mini mill - by dallen - 08-01-2012, 11:41 AM

RE: mini mill - by Mayhem - 08-01-2012, 07:37 PM

RE: mini mill - by dallen - 08-01-2012, 09:13 PM

Users browsing this thread: 8 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me