|
Project Mini Lathe Mods
|
06-03-2024, 11:27 AM
(06-03-2024, 09:10 AM)rleete Wrote: Halfway there. I'm going to use the PLA model for marking out for the holes. That is after I've made sure the PLA model and steel riser block bolt together properly. I did buy two disks just in case I screw up the first one.  Ed |
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Mini Lathe Mods - by EdK - 05-27-2024, 02:43 PM
RE: Mini Lathe Mods - by JScott - 05-27-2024, 04:01 PM
RE: Mini Lathe Mods - by EdK - 05-27-2024, 04:20 PM
RE: Mini Lathe Mods - by rleete - 05-27-2024, 06:36 PM
RE: Mini Lathe Mods - by EdK - 05-27-2024, 06:41 PM
RE: Mini Lathe Mods - by EdK - 06-01-2024, 05:23 PM
RE: Mini Lathe Mods - by EdK - 06-02-2024, 08:50 PM
RE: Mini Lathe Mods - by Highpower - 06-03-2024, 03:46 PM
RE: Mini Lathe Mods - by rleete - 06-03-2024, 09:10 AM
RE: Mini Lathe Mods - by EdK - 06-03-2024, 11:27 AM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 12:46 AM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 02:06 PM
RE: Mini Lathe Mods - by rleete - 06-04-2024, 03:11 PM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 04:42 PM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 04:45 PM
RE: Mini Lathe Mods - by rleete - 06-04-2024, 04:56 PM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 06:04 PM
RE: Mini Lathe Mods - by rleete - 06-05-2024, 09:48 AM
RE: Mini Lathe Mods - by EdK - 06-05-2024, 12:36 PM
RE: Mini Lathe Mods - by EdK - 06-11-2024, 12:21 PM
RE: Mini Lathe Mods - by rleete - 06-20-2024, 06:37 AM
RE: Mini Lathe Mods - by EdK - 06-20-2024, 11:45 AM
RE: Mini Lathe Mods - by EdK - 08-19-2024, 01:35 AM
RE: Mini Lathe Mods - by rleete - 08-19-2024, 09:22 AM
RE: Mini Lathe Mods - by EdK - 08-25-2024, 04:46 PM
RE: Mini Lathe Mods - by Highpower - 08-25-2024, 05:31 PM
RE: Mini Lathe Mods - by EdK - 08-25-2024, 11:38 PM
RE: Mini Lathe Mods - by JScott - 08-25-2024, 06:46 PM
RE: Mini Lathe Mods - by rleete - 08-26-2024, 07:02 AM
RE: Mini Lathe Mods - by EdK - 08-26-2024, 12:46 PM
|
