MetalworkingFun Forum › Machinery › Lathes v
[PROJECT] Mini Lathe Mods

Thread Modes
Project Mini Lathe Mods
rleete Offline
Senior
*****
Posts: 771
Threads: 48
Joined: Mar 2012
Location: Rochester, NY
#8
06-03-2024, 09:10 AM
Halfway there.

If you enlarge the hole to match the riser block, you can use that as a template for marking out the holes.
Full of ideas, but slow to produce parts
Reply
Thanks given by: EdK


Messages In This Thread
Mini Lathe Mods - by EdK - 05-27-2024, 02:43 PM
RE: Mini Lathe Mods - by JScott - 05-27-2024, 04:01 PM
RE: Mini Lathe Mods - by EdK - 05-27-2024, 04:20 PM
RE: Mini Lathe Mods - by rleete - 05-27-2024, 06:36 PM
RE: Mini Lathe Mods - by EdK - 05-27-2024, 06:41 PM
RE: Mini Lathe Mods - by EdK - 06-01-2024, 05:23 PM
RE: Mini Lathe Mods - by EdK - 06-02-2024, 08:50 PM
RE: Mini Lathe Mods - by Highpower - 06-03-2024, 03:46 PM
RE: Mini Lathe Mods - by rleete - 06-03-2024, 09:10 AM
RE: Mini Lathe Mods - by EdK - 06-03-2024, 11:27 AM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 12:46 AM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 02:06 PM
RE: Mini Lathe Mods - by rleete - 06-04-2024, 03:11 PM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 04:42 PM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 04:45 PM
RE: Mini Lathe Mods - by rleete - 06-04-2024, 04:56 PM
RE: Mini Lathe Mods - by EdK - 06-04-2024, 06:04 PM
RE: Mini Lathe Mods - by rleete - 06-05-2024, 09:48 AM
RE: Mini Lathe Mods - by EdK - 06-05-2024, 12:36 PM
RE: Mini Lathe Mods - by EdK - 06-11-2024, 12:21 PM
RE: Mini Lathe Mods - by rleete - 06-20-2024, 06:37 AM
RE: Mini Lathe Mods - by EdK - 06-20-2024, 11:45 AM
RE: Mini Lathe Mods - by EdK - 08-19-2024, 01:35 AM
RE: Mini Lathe Mods - by rleete - 08-19-2024, 09:22 AM
RE: Mini Lathe Mods - by EdK - 08-25-2024, 04:46 PM
RE: Mini Lathe Mods - by Highpower - 08-25-2024, 05:31 PM
RE: Mini Lathe Mods - by EdK - 08-25-2024, 11:38 PM
RE: Mini Lathe Mods - by JScott - 08-25-2024, 06:46 PM
RE: Mini Lathe Mods - by rleete - 08-26-2024, 07:02 AM
RE: Mini Lathe Mods - by EdK - 08-26-2024, 12:46 PM



Users browsing this thread: 7 Guest(s)