MetalworkingFun Forum › Machinery › Milling Machines v
Wabeco F1200

Thread Modes
Wabeco F1200
Wongster Offline
Junior
****
Posts: 301
Threads: 30
Joined: Mar 2012
Location: Singapore
#26
07-08-2012, 07:50 PM
Dave,

What about the length? How much over hang should I allow?

I saw Kurt vise on some US site. The cheapest is quite off my budget. So I'll have look for something that's as close without burning a hole in my wallet.

Regards,
Wong
Wongster
http://www.wongstersproduction.com

Proud to be a member of MetalworkingFun Forum since Mar 2012.
Reply
Thanks given by:


Messages In This Thread
Wabeco F1200 - by Wongster - 07-07-2012, 10:15 AM
RE: Wabeco F1200 - by DaveH - 07-07-2012, 10:37 AM
RE: Wabeco F1200 - by doubleboost - 07-07-2012, 10:46 AM
RE: Wabeco F1200 - by Wongster - 07-07-2012, 11:05 AM
RE: Wabeco F1200 - by DaveH - 07-07-2012, 11:39 AM
RE: Wabeco F1200 - by Sunset Machine - 07-07-2012, 01:14 PM
RE: Wabeco F1200 - by DaveH - 07-07-2012, 02:39 PM
RE: Wabeco F1200 - by doubleboost - 07-07-2012, 04:41 PM
RE: Wabeco F1200 - by Wongster - 07-07-2012, 07:26 PM
RE: Wabeco F1200 - by TOM REED - 07-07-2012, 09:16 PM
RE: Wabeco F1200 - by Wongster - 07-07-2012, 09:39 PM
RE: Wabeco F1200 - by Highpower - 07-07-2012, 10:34 PM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 12:25 AM
RE: Wabeco F1200 - by DaveH - 07-08-2012, 06:22 AM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 07:30 AM
RE: Wabeco F1200 - by Highpower - 07-08-2012, 08:30 AM
RE: Wabeco F1200 - by DaveH - 07-08-2012, 08:57 AM
RE: Wabeco F1200 - by DaveH - 07-08-2012, 09:12 AM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 09:32 AM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 09:36 AM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 05:42 PM
RE: Wabeco F1200 - by DaveH - 07-08-2012, 05:58 PM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 06:41 PM
RE: Wabeco F1200 - by DaveH - 07-08-2012, 07:26 PM
RE: Wabeco F1200 - by DaveH - 07-08-2012, 07:42 PM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 08:02 PM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 07:50 PM
RE: Wabeco F1200 - by f350ca - 07-08-2012, 08:52 PM
RE: Wabeco F1200 - by Wongster - 07-08-2012, 09:04 PM
RE: Wabeco F1200 - by f350ca - 07-08-2012, 09:28 PM
RE: Wabeco F1200 - by Mayhem - 07-09-2012, 04:34 AM
RE: Wabeco F1200 - by DaveH - 07-09-2012, 04:34 AM
RE: Wabeco F1200 - by Wongster - 07-09-2012, 06:17 AM
RE: Wabeco F1200 - by Mayhem - 07-09-2012, 07:51 AM
RE: Wabeco F1200 - by DaveH - 07-09-2012, 08:29 AM
RE: Wabeco F1200 - by Wongster - 07-09-2012, 09:48 AM
RE: Wabeco F1200 - by Wongster - 07-09-2012, 10:05 AM
RE: Wabeco F1200 - by DaveH - 07-09-2012, 11:51 AM
RE: Wabeco F1200 - by Wongster - 07-09-2012, 11:56 AM
RE: Wabeco F1200 - by TOM REED - 07-09-2012, 12:26 PM
RE: Wabeco F1200 - by stevec - 07-09-2012, 03:27 PM
RE: Wabeco F1200 - by doubleboost - 07-09-2012, 04:24 PM
RE: Wabeco F1200 - by Wongster - 07-09-2012, 05:20 PM
RE: Wabeco F1200 - by Mayhem - 07-10-2012, 07:47 AM
RE: Wabeco F1200 - by Wongster - 07-10-2012, 09:43 AM
RE: Wabeco F1200 - by Mayhem - 07-10-2012, 09:47 AM
RE: Wabeco F1200 - by Wongster - 07-10-2012, 10:45 AM
RE: Wabeco F1200 - by Wongster - 07-14-2012, 01:52 AM
RE: Wabeco F1200 - by DaveH - 07-14-2012, 05:58 AM
RE: Wabeco F1200 - by Wongster - 07-14-2012, 06:30 AM
RE: Wabeco F1200 - by krv3000 - 07-14-2012, 05:46 PM
RE: Wabeco F1200 - by ETC57 - 07-14-2012, 07:18 PM
RE: Wabeco F1200 - by Wongster - 07-14-2012, 08:14 PM



Users browsing this thread: 4 Guest(s)