MetalworkingFun Forum › Machinery › Lathes v
Mini-Lathe Bearing Puller

Thread Modes
Mini-Lathe Bearing Puller
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#24
06-08-2023, 08:05 AM
Graemlin
Remember - that puller kit was designed to remove and install the factory standard size deep groove ball bearings. If you are installing tapered roller bearings or the angular contact type ball bearings you have to compensate for the race differences on your own I'm afraid. But you managed that like a boss! Thumbsup

I never press fit bearings dry. Always use a bit of light lubrication.
Willie
Reply
Thanks given by: EdK


Messages In This Thread
Mini-Lathe Bearing Puller - by EdK - 08-22-2022, 12:53 PM
RE: Mini-Lathe Bearing Puller - by Dr Stan - 08-22-2022, 09:29 PM
RE: Mini-Lathe Bearing Puller - by rleete - 08-23-2022, 07:34 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 08-23-2022, 08:29 AM
RE: Mini-Lathe Bearing Puller - by EdK - 08-23-2022, 11:51 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 08-23-2022, 03:15 PM
RE: Mini-Lathe Bearing Puller - by chucketn - 08-23-2022, 12:09 PM
RE: Mini-Lathe Bearing Puller - by EdK - 08-23-2022, 02:09 PM
RE: Mini-Lathe Bearing Puller - by chucketn - 08-24-2022, 01:52 PM
RE: Mini-Lathe Bearing Puller - by EdK - 08-28-2022, 05:08 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 08-28-2022, 06:26 PM
RE: Mini-Lathe Bearing Puller - by EdK - 09-08-2022, 04:05 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-05-2023, 06:22 PM
RE: Mini-Lathe Bearing Puller - by Vinny - 06-06-2023, 09:26 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-06-2023, 03:49 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-06-2023, 08:52 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-06-2023, 10:17 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-07-2023, 08:48 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-07-2023, 10:31 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-07-2023, 04:10 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-07-2023, 06:11 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-07-2023, 08:02 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-08-2023, 12:54 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-08-2023, 08:05 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-08-2023, 12:00 PM
RE: Mini-Lathe Bearing Puller - by Vinny - 06-08-2023, 09:36 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-08-2023, 12:01 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-11-2023, 02:34 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-11-2023, 05:33 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-11-2023, 07:19 PM
RE: Mini-Lathe Bearing Puller - by rleete - 06-11-2023, 07:43 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-11-2023, 08:26 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-12-2023, 08:48 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-12-2023, 10:37 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-14-2023, 10:48 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-14-2023, 12:37 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-14-2023, 03:26 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-14-2023, 09:22 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-14-2023, 10:05 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-15-2023, 08:45 AM
RE: Mini-Lathe Bearing Puller - by rleete - 06-15-2023, 09:35 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 10:54 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 10:51 AM
RE: Mini-Lathe Bearing Puller - by rleete - 06-15-2023, 11:45 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 11:48 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-15-2023, 07:50 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 09:01 PM
RE: Mini-Lathe Bearing Puller - by Vinny - 06-15-2023, 04:48 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-16-2023, 03:36 PM
RE: Mini-Lathe Bearing Puller - by rleete - 06-16-2023, 04:01 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-16-2023, 04:34 PM
RE: Mini-Lathe Bearing Puller - by EdK - 07-06-2023, 05:28 PM



Users browsing this thread: 2 Guest(s)