MetalworkingFun Forum › Machinery › Lathes v
Mini-Lathe Bearing Puller

Thread Modes
Mini-Lathe Bearing Puller
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#5
08-23-2022, 11:51 AM
(08-23-2022, 08:29 AM)Highpower Wrote: The collar with the keyway on sheet 3 is not needed for the puller set.

I haven't read the instructions yet. I knew I should have because I know some of the parts in the kit are not used for pulling the bearings.  Big Grin

Thanks for the clarification.  Thumbsup

I think I'll change the drawing and put the two gears and the collar on a separate sheet with a note on it.  Chin

Ed
Reply
Thanks given by:


Messages In This Thread
Mini-Lathe Bearing Puller - by EdK - 08-22-2022, 12:53 PM
RE: Mini-Lathe Bearing Puller - by Dr Stan - 08-22-2022, 09:29 PM
RE: Mini-Lathe Bearing Puller - by rleete - 08-23-2022, 07:34 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 08-23-2022, 08:29 AM
RE: Mini-Lathe Bearing Puller - by EdK - 08-23-2022, 11:51 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 08-23-2022, 03:15 PM
RE: Mini-Lathe Bearing Puller - by chucketn - 08-23-2022, 12:09 PM
RE: Mini-Lathe Bearing Puller - by EdK - 08-23-2022, 02:09 PM
RE: Mini-Lathe Bearing Puller - by chucketn - 08-24-2022, 01:52 PM
RE: Mini-Lathe Bearing Puller - by EdK - 08-28-2022, 05:08 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 08-28-2022, 06:26 PM
RE: Mini-Lathe Bearing Puller - by EdK - 09-08-2022, 04:05 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-05-2023, 06:22 PM
RE: Mini-Lathe Bearing Puller - by Vinny - 06-06-2023, 09:26 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-06-2023, 03:49 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-06-2023, 08:52 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-06-2023, 10:17 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-07-2023, 08:48 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-07-2023, 10:31 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-07-2023, 04:10 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-07-2023, 06:11 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-07-2023, 08:02 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-08-2023, 12:54 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-08-2023, 08:05 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-08-2023, 12:00 PM
RE: Mini-Lathe Bearing Puller - by Vinny - 06-08-2023, 09:36 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-08-2023, 12:01 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-11-2023, 02:34 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-11-2023, 05:33 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-11-2023, 07:19 PM
RE: Mini-Lathe Bearing Puller - by rleete - 06-11-2023, 07:43 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-11-2023, 08:26 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-12-2023, 08:48 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-12-2023, 10:37 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-14-2023, 10:48 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-14-2023, 12:37 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-14-2023, 03:26 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-14-2023, 09:22 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-14-2023, 10:05 PM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-15-2023, 08:45 AM
RE: Mini-Lathe Bearing Puller - by rleete - 06-15-2023, 09:35 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 10:54 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 10:51 AM
RE: Mini-Lathe Bearing Puller - by rleete - 06-15-2023, 11:45 AM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 11:48 AM
RE: Mini-Lathe Bearing Puller - by Highpower - 06-15-2023, 07:50 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-15-2023, 09:01 PM
RE: Mini-Lathe Bearing Puller - by Vinny - 06-15-2023, 04:48 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-16-2023, 03:36 PM
RE: Mini-Lathe Bearing Puller - by rleete - 06-16-2023, 04:01 PM
RE: Mini-Lathe Bearing Puller - by EdK - 06-16-2023, 04:34 PM
RE: Mini-Lathe Bearing Puller - by EdK - 07-06-2023, 05:28 PM



Users browsing this thread: 3 Guest(s)