Part support while milling

Hello There, Guest! Register

Thread Modes

Part support while milling

Highpower Offline

Offline

JAFO

Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA

The following 3 users Like Highpower's post:
EdK (10-23-2019), f350ca (10-23-2019), Vinny (10-23-2019)

#3

10-22-2019, 11:15 PM

Or make a fixture plate (aluminum is popular) that will screw to your rotary table and you have a clean flat surface that you can drill and tap anywhere you want for clamping plates. You can cut into it many times without harming the tables surface, and once it gets too chewed up you can mill the top of the plate flat again. Or just make another one.

Size and shape to your desire. Smile

Smile

https://www.youtube.com/watch?v=SiRoeOop1v4

Willie

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Part support while milling - by Paulc - 10-22-2019, 09:17 PM

RE: Part support while milling - by Hawkeye - 10-22-2019, 10:22 PM

RE: Part support while milling - by Highpower - 10-22-2019, 11:15 PM

RE: Part support while milling - by rleete - 10-23-2019, 10:08 AM

RE: Part support while milling - by Paulc - 10-23-2019, 11:29 AM

RE: Part support while milling - by Vinny - 10-23-2019, 02:40 PM

RE: Part support while milling - by Highpower - 10-23-2019, 11:10 PM

RE: Part support while milling - by Paulc - 10-23-2019, 02:44 PM

RE: Part support while milling - by Highpower - 10-23-2019, 07:35 PM

RE: Part support while milling - by Paulc - 10-23-2019, 08:47 PM

RE: Part support while milling - by TomG - 10-23-2019, 10:59 PM

RE: Part support while milling - by Vinny - 10-24-2019, 02:02 PM

RE: Part support while milling - by Highpower - 10-24-2019, 07:15 PM

RE: Part support while milling - by Vinny - 10-24-2019, 11:13 PM

RE: Part support while milling - by Highpower - 10-25-2019, 09:30 AM

RE: Part support while milling - by f350ca - 10-25-2019, 02:01 PM

RE: Part support while milling - by Highpower - 10-25-2019, 04:15 PM

RE: Part support while milling - by f350ca - 10-25-2019, 05:12 PM

RE: Part support while milling - by Highpower - 10-25-2019, 11:57 PM

RE: Part support while milling - by Highpower - 10-29-2019, 08:46 AM

RE: Part support while milling - by Paulc - 10-29-2019, 12:44 PM

RE: Part support while milling - by Dr Stan - 10-29-2019, 12:47 PM

RE: Part support while milling - by Paulc - 10-29-2019, 02:39 PM

RE: Part support while milling - by Highpower - 10-29-2019, 03:47 PM

RE: Part support while milling - by Paulc - 10-29-2019, 10:34 PM

RE: Part support while milling - by Highpower - 10-30-2019, 06:23 AM

RE: Part support while milling - by Paulc - 10-30-2019, 09:46 PM

RE: Part support while milling - by Vinny - 11-01-2019, 02:54 PM

RE: Part support while milling - by Highpower - 11-01-2019, 11:41 PM

RE: Part support while milling - by Vinny - 11-03-2019, 06:37 PM

RE: Part support while milling - by rleete - 11-04-2019, 09:17 AM

Users browsing this thread: 3 Guest(s)