Part support while milling

Hello There, Guest! Register

Thread Modes

Part support while milling

Hawkeye Offline

Offline

Junior

Posts: 535
Threads: 39
Joined: Jan 2013
Location: Kelowna, BC, Canada

The following 3 users Like Hawkeye's post:
Highpower (10-22-2019), Dr Stan (10-22-2019), Hopefuldave (01-08-2020)

#2

10-22-2019, 10:22 PM

MDF or other fairly 'precise' particle board makes a good sacrificial backing.

Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Part support while milling - by Paulc - 10-22-2019, 09:17 PM

RE: Part support while milling - by Hawkeye - 10-22-2019, 10:22 PM

RE: Part support while milling - by Highpower - 10-22-2019, 11:15 PM

RE: Part support while milling - by rleete - 10-23-2019, 10:08 AM

RE: Part support while milling - by Paulc - 10-23-2019, 11:29 AM

RE: Part support while milling - by Vinny - 10-23-2019, 02:40 PM

RE: Part support while milling - by Highpower - 10-23-2019, 11:10 PM

RE: Part support while milling - by Paulc - 10-23-2019, 02:44 PM

RE: Part support while milling - by Highpower - 10-23-2019, 07:35 PM

RE: Part support while milling - by Paulc - 10-23-2019, 08:47 PM

RE: Part support while milling - by TomG - 10-23-2019, 10:59 PM

RE: Part support while milling - by Vinny - 10-24-2019, 02:02 PM

RE: Part support while milling - by Highpower - 10-24-2019, 07:15 PM

RE: Part support while milling - by Vinny - 10-24-2019, 11:13 PM

RE: Part support while milling - by Highpower - 10-25-2019, 09:30 AM

RE: Part support while milling - by f350ca - 10-25-2019, 02:01 PM

RE: Part support while milling - by Highpower - 10-25-2019, 04:15 PM

RE: Part support while milling - by f350ca - 10-25-2019, 05:12 PM

RE: Part support while milling - by Highpower - 10-25-2019, 11:57 PM

RE: Part support while milling - by Highpower - 10-29-2019, 08:46 AM

RE: Part support while milling - by Paulc - 10-29-2019, 12:44 PM

RE: Part support while milling - by Dr Stan - 10-29-2019, 12:47 PM

RE: Part support while milling - by Paulc - 10-29-2019, 02:39 PM

RE: Part support while milling - by Highpower - 10-29-2019, 03:47 PM

RE: Part support while milling - by Paulc - 10-29-2019, 10:34 PM

RE: Part support while milling - by Highpower - 10-30-2019, 06:23 AM

RE: Part support while milling - by Paulc - 10-30-2019, 09:46 PM

RE: Part support while milling - by Vinny - 11-01-2019, 02:54 PM

RE: Part support while milling - by Highpower - 11-01-2019, 11:41 PM

RE: Part support while milling - by Vinny - 11-03-2019, 06:37 PM

RE: Part support while milling - by rleete - 11-04-2019, 09:17 AM

Users browsing this thread: 6 Guest(s)