Quick Question Thread

Hello There, Guest! Register

Thread Modes

Quick Question Thread

Highpower Offline

Offline

JAFO

Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA

#28

10-02-2019, 03:27 PM

(10-01-2019, 12:40 PM)Vinny Wrote: The problem with the 2" stuff is, where did I put it?

I'm in the same boat. I have a set of R-8 end mill holders... somewhere. I pulled them out of my 'tooling' cabinet to make room for other 'more often' used items instead, and haven't seen them since - except for the 1/8" end mill holder I always keep in the collet rack with a 1/8" carbide starting drill in it.

They are in a box buried somewhere in my basement, probably along with my vise stops that I can't find either.

Willie

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Quick Question Thread - by f350ca - 02-20-2019, 12:52 PM

RE: Quick Question Thread - by Dr Stan - 02-20-2019, 01:17 PM

RE: Quick Question Thread - by arvidj - 02-20-2019, 01:52 PM

RE: Quick Question Thread - by f350ca - 02-20-2019, 05:41 PM

RE: Quick Question Thread - by Dr Stan - 02-21-2019, 10:41 AM

RE: Quick Question Thread - by arvidj - 02-21-2019, 11:10 AM

RE: Quick Question Thread - by Dr Stan - 02-22-2019, 10:46 AM

RE: Quick Question Thread - by Pete O - 02-22-2019, 10:04 PM

RE: Quick Question Thread - by f350ca - 02-22-2019, 10:39 PM

RE: Quick Question Thread - by Clifford B. - 02-22-2019, 11:36 PM

RE: Quick Question Thread - by Dr Stan - 02-23-2019, 11:02 AM

RE: Quick Question Thread - by Highpower - 02-23-2019, 11:55 AM

RE: Quick Question Thread - by Dr Stan - 02-23-2019, 03:43 PM

RE: Quick Question Thread - by Dr Stan - 06-18-2023, 07:55 PM

RE: Quick Question Thread - by chucketn - 02-23-2019, 01:58 PM

RE: Quick Question Thread - by TomG - 02-23-2019, 03:40 PM

RE: Quick Question Thread - by chucketn - 02-23-2019, 06:24 PM

RE: Quick Question Thread - by Pete O - 03-27-2019, 05:53 AM

RE: Quick Question Thread - by TomG - 03-27-2019, 06:50 AM

RE: Quick Question Thread - by Pete O - 03-27-2019, 07:35 AM

RE: Quick Question Thread - by TomG - 03-27-2019, 08:21 AM

RE: Quick Question Thread - by Vinny - 09-29-2019, 11:37 AM

RE: Quick Question Thread - by f350ca - 09-29-2019, 12:31 PM

RE: Quick Question Thread - by Vinny - 09-29-2019, 04:41 PM

RE: Quick Question Thread - by rleete - 09-30-2019, 03:25 PM

RE: Quick Question Thread - by Dr Stan - 10-01-2019, 08:15 AM

RE: Quick Question Thread - by Vinny - 10-01-2019, 12:40 PM

RE: Quick Question Thread - by Highpower - 10-02-2019, 03:27 PM

RE: Quick Question Thread - Quorn sharpener - by arvidj - 10-01-2019, 12:58 PM

RE: Quick Question Thread - Quorn sharpener - by Highpower - 10-03-2019, 11:28 PM

RE: Quick Question Thread - Quorn sharpener - by EdK - 10-04-2019, 12:21 AM

RE: Quick Question Thread - Quorn sharpener - by Highpower - 10-04-2019, 11:39 AM

RE: Quick Question Thread - by Vinny - 10-03-2019, 11:04 PM

RE: Quick Question Thread - by Highpower - 10-03-2019, 11:46 PM

RE: Quick Question Thread - by Vinny - 10-04-2019, 07:54 AM

RE: Quick Question Thread - by Vinny - 10-04-2019, 08:15 AM

RE: Quick Question Thread - by Highpower - 10-04-2019, 11:41 AM

RE: Quick Question Thread - by Dr Stan - 10-04-2019, 01:01 PM

RE: Quick Question Thread - by Vinny - 10-04-2019, 07:24 PM

RE: Quick Question Thread - by Highpower - 10-04-2019, 07:53 PM

RE: Quick Question Thread - by Dr Stan - 04-09-2023, 08:57 AM

RE: Quick Question Thread - by Vinny - 04-09-2023, 09:06 AM

RE: Quick Question Thread - by Dr Stan - 04-09-2023, 07:05 PM

RE: Quick Question Thread - by Vinny - 04-09-2023, 07:20 PM

RE: Quick Question Thread - by Dr Stan - 04-10-2023, 07:12 AM

RE: Quick Question Thread - by Vinny - 04-11-2023, 03:28 PM

Users browsing this thread: 2 Guest(s)