MetalworkingFun Forum › Machining › General Metalworking Discussion v
Quick Question Thread

Thread Modes
Quick Question Thread
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#14
02-23-2019, 03:40 PM
It's a 6% silver solder and melts at 430ºF, so it should work fine with MAPP gas, as long as the plates/parts are not too large.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:


Messages In This Thread
Quick Question Thread - by f350ca - 02-20-2019, 12:52 PM
RE: Quick Question Thread - by Dr Stan - 02-20-2019, 01:17 PM
RE: Quick Question Thread - by arvidj - 02-20-2019, 01:52 PM
RE: Quick Question Thread - by f350ca - 02-20-2019, 05:41 PM
RE: Quick Question Thread - by Dr Stan - 02-21-2019, 10:41 AM
RE: Quick Question Thread - by arvidj - 02-21-2019, 11:10 AM
RE: Quick Question Thread - by Dr Stan - 02-22-2019, 10:46 AM
RE: Quick Question Thread - by Pete O - 02-22-2019, 10:04 PM
RE: Quick Question Thread - by f350ca - 02-22-2019, 10:39 PM
RE: Quick Question Thread - by Clifford B. - 02-22-2019, 11:36 PM
RE: Quick Question Thread - by Dr Stan - 02-23-2019, 11:02 AM
RE: Quick Question Thread - by Highpower - 02-23-2019, 11:55 AM
RE: Quick Question Thread - by Dr Stan - 02-23-2019, 03:43 PM
RE: Quick Question Thread - by Dr Stan - 06-18-2023, 07:55 PM
RE: Quick Question Thread - by chucketn - 02-23-2019, 01:58 PM
RE: Quick Question Thread - by TomG - 02-23-2019, 03:40 PM
RE: Quick Question Thread - by chucketn - 02-23-2019, 06:24 PM
RE: Quick Question Thread - by Pete O - 03-27-2019, 05:53 AM
RE: Quick Question Thread - by TomG - 03-27-2019, 06:50 AM
RE: Quick Question Thread - by Pete O - 03-27-2019, 07:35 AM
RE: Quick Question Thread - by TomG - 03-27-2019, 08:21 AM
RE: Quick Question Thread - by Vinny - 09-29-2019, 11:37 AM
RE: Quick Question Thread - by f350ca - 09-29-2019, 12:31 PM
RE: Quick Question Thread - by Vinny - 09-29-2019, 04:41 PM
RE: Quick Question Thread - by rleete - 09-30-2019, 03:25 PM
RE: Quick Question Thread - by Dr Stan - 10-01-2019, 08:15 AM
RE: Quick Question Thread - by Vinny - 10-01-2019, 12:40 PM
RE: Quick Question Thread - by Highpower - 10-02-2019, 03:27 PM
RE: Quick Question Thread - by Vinny - 10-03-2019, 11:04 PM
RE: Quick Question Thread - by Highpower - 10-03-2019, 11:46 PM
RE: Quick Question Thread - by Vinny - 10-04-2019, 07:54 AM
RE: Quick Question Thread - by Vinny - 10-04-2019, 08:15 AM
RE: Quick Question Thread - by Highpower - 10-04-2019, 11:41 AM
RE: Quick Question Thread - by Dr Stan - 10-04-2019, 01:01 PM
RE: Quick Question Thread - by Vinny - 10-04-2019, 07:24 PM
RE: Quick Question Thread - by Highpower - 10-04-2019, 07:53 PM
RE: Quick Question Thread - by Dr Stan - 04-09-2023, 08:57 AM
RE: Quick Question Thread - by Vinny - 04-09-2023, 09:06 AM
RE: Quick Question Thread - by Dr Stan - 04-09-2023, 07:05 PM
RE: Quick Question Thread - by Vinny - 04-09-2023, 07:20 PM
RE: Quick Question Thread - by Dr Stan - 04-10-2023, 07:12 AM
RE: Quick Question Thread - by Vinny - 04-11-2023, 03:28 PM



Users browsing this thread: 3 Guest(s)