Grandfather Clock
#37
Another way to check the theorem would be to make a pendulum with a disk bolted on the end. Start the swing and a stopwatch at the same time and time, say, ten swings. Then bolt a second disk on at the same location. Time it again. This will tell you if added weight changes the effective length.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:


Messages In This Thread
Grandfather Clock - by Vinny - 02-12-2019, 10:05 PM
RE: Grandfather Clock - by f350ca - 02-12-2019, 11:19 PM
RE: Grandfather Clock - by Vinny - 02-13-2019, 12:00 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 12:18 AM
RE: Grandfather Clock - by TomG - 02-13-2019, 01:04 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 01:41 AM
RE: Grandfather Clock - by TomG - 02-13-2019, 08:06 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 11:04 AM
RE: Grandfather Clock - by TomG - 02-13-2019, 12:57 PM
RE: Grandfather Clock - by Vinny - 02-13-2019, 11:11 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 01:41 PM
RE: Grandfather Clock - by Highpower - 02-14-2019, 11:47 AM
RE: Grandfather Clock - by Vinny - 02-14-2019, 12:01 PM
RE: Grandfather Clock - by Highpower - 02-14-2019, 01:16 PM
RE: Grandfather Clock - by TomG - 02-14-2019, 03:47 PM
RE: Grandfather Clock - by Vinny - 02-15-2019, 11:00 PM
RE: Grandfather Clock - by Vinny - 02-16-2019, 01:41 AM
RE: Grandfather Clock - by TomG - 02-16-2019, 09:02 AM
RE: Grandfather Clock - by f350ca - 02-16-2019, 09:25 AM
RE: Grandfather Clock - by Highpower - 02-16-2019, 02:15 PM
RE: Grandfather Clock - by TomG - 02-16-2019, 08:13 PM
RE: Grandfather Clock - by Dr Stan - 02-18-2019, 08:55 AM
RE: Grandfather Clock - by TomG - 02-18-2019, 09:21 AM
RE: Grandfather Clock - by Vinny - 02-18-2019, 10:06 PM
RE: Grandfather Clock - by f350ca - 02-19-2019, 09:09 AM
RE: Grandfather Clock - by TomG - 02-19-2019, 11:20 AM
RE: Grandfather Clock - by Vinny - 02-19-2019, 03:37 PM
RE: Grandfather Clock - by haroldmulder - 02-19-2019, 08:38 PM
RE: Grandfather Clock - by TomG - 02-19-2019, 10:25 PM
RE: Grandfather Clock - by Vinny - 02-20-2019, 09:42 AM
RE: Grandfather Clock - by Vinny - 02-20-2019, 09:43 AM
RE: Grandfather Clock - by Dr Stan - 02-20-2019, 01:19 PM
RE: Grandfather Clock - by Vinny - 02-20-2019, 03:01 PM
RE: Grandfather Clock - by f350ca - 02-20-2019, 05:44 PM
RE: Grandfather Clock - by TomG - 02-20-2019, 06:02 PM
RE: Grandfather Clock - by Vinny - 02-21-2019, 01:18 PM
RE: Grandfather Clock - by Hawkeye - 02-21-2019, 11:23 PM
RE: Grandfather Clock - by TomG - 02-22-2019, 12:11 AM
RE: Grandfather Clock - by wawoodman - 09-23-2019, 06:48 PM



Users browsing this thread: 2 Guest(s)