MetalworkingFun Forum › Machining › Horology
Grandfather Clock

Thread Modes
Grandfather Clock
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#34
02-20-2019, 05:44 PM
The combination of the shaft and bob make up the pendulum, as they said a heavier bob would lower the center of gravity effectively increasing the length of the combination.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
Grandfather Clock - by Vinny - 02-12-2019, 10:05 PM
RE: Grandfather Clock - by f350ca - 02-12-2019, 11:19 PM
RE: Grandfather Clock - by Vinny - 02-13-2019, 12:00 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 12:18 AM
RE: Grandfather Clock - by TomG - 02-13-2019, 01:04 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 01:41 AM
RE: Grandfather Clock - by TomG - 02-13-2019, 08:06 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 11:04 AM
RE: Grandfather Clock - by TomG - 02-13-2019, 12:57 PM
RE: Grandfather Clock - by Vinny - 02-13-2019, 11:11 AM
RE: Grandfather Clock - by Vinny - 02-13-2019, 01:41 PM
RE: Grandfather Clock - by Highpower - 02-14-2019, 11:47 AM
RE: Grandfather Clock - by Vinny - 02-14-2019, 12:01 PM
RE: Grandfather Clock - by Highpower - 02-14-2019, 01:16 PM
RE: Grandfather Clock - by TomG - 02-14-2019, 03:47 PM
RE: Grandfather Clock - by Vinny - 02-15-2019, 11:00 PM
RE: Grandfather Clock - by Vinny - 02-16-2019, 01:41 AM
RE: Grandfather Clock - by TomG - 02-16-2019, 09:02 AM
RE: Grandfather Clock - by f350ca - 02-16-2019, 09:25 AM
RE: Grandfather Clock - by Highpower - 02-16-2019, 02:15 PM
RE: Grandfather Clock - by TomG - 02-16-2019, 08:13 PM
RE: Grandfather Clock - by Dr Stan - 02-18-2019, 08:55 AM
RE: Grandfather Clock - by TomG - 02-18-2019, 09:21 AM
RE: Grandfather Clock - by Vinny - 02-18-2019, 10:06 PM
RE: Grandfather Clock - by f350ca - 02-19-2019, 09:09 AM
RE: Grandfather Clock - by TomG - 02-19-2019, 11:20 AM
RE: Grandfather Clock - by Vinny - 02-19-2019, 03:37 PM
RE: Grandfather Clock - by haroldmulder - 02-19-2019, 08:38 PM
RE: Grandfather Clock - by TomG - 02-19-2019, 10:25 PM
RE: Grandfather Clock - by Vinny - 02-20-2019, 09:42 AM
RE: Grandfather Clock - by Vinny - 02-20-2019, 09:43 AM
RE: Grandfather Clock - by Dr Stan - 02-20-2019, 01:19 PM
RE: Grandfather Clock - by Vinny - 02-20-2019, 03:01 PM
RE: Grandfather Clock - by f350ca - 02-20-2019, 05:44 PM
RE: Grandfather Clock - by TomG - 02-20-2019, 06:02 PM
RE: Grandfather Clock - by Vinny - 02-21-2019, 01:18 PM
RE: Grandfather Clock - by Hawkeye - 02-21-2019, 11:23 PM
RE: Grandfather Clock - by TomG - 02-22-2019, 12:11 AM
RE: Grandfather Clock - by wawoodman - 09-23-2019, 06:48 PM



Users browsing this thread: 1 Guest(s)