MetalworkingFun Forum › Machining › General Metalworking Discussion v
Need some hold down advice

Thread Modes
Need some hold down advice
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#25
02-18-2018, 09:08 AM
Not sure how much you are planning to take off, but light cuts are in order. It's also worth starting the cut over the work, rather than off to the side. Any lifting of the part is a bad thing.  Big Grin

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:


Messages In This Thread
Need some hold down advice - by Vinny - 02-02-2018, 01:27 PM
RE: Need some hold down advice - by dallen - 02-02-2018, 01:52 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 02:17 PM
RE: Need some hold down advice - by wawoodman - 02-02-2018, 02:55 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 03:02 PM
RE: Need some hold down advice - by Dr Stan - 02-02-2018, 03:43 PM
RE: Need some hold down advice - by TomG - 02-02-2018, 04:16 PM
RE: Need some hold down advice - by randyc - 02-02-2018, 04:38 PM
RE: Need some hold down advice - by Highpower - 02-02-2018, 05:31 PM
RE: Need some hold down advice - by f350ca - 02-02-2018, 05:47 PM
RE: Need some hold down advice - by randyc - 02-02-2018, 06:08 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 06:51 PM
RE: Need some hold down advice - by kwoodhands - 03-02-2018, 02:52 PM
RE: Need some hold down advice - by SteveG - 02-02-2018, 08:55 PM
RE: Need some hold down advice - by wawoodman - 02-03-2018, 06:41 PM
RE: Need some hold down advice - by Vinny - 02-03-2018, 07:55 PM
RE: Need some hold down advice - by TomG - 02-04-2018, 04:11 PM
RE: Need some hold down advice - by Vinny - 02-04-2018, 04:36 PM
RE: Need some hold down advice - by Highpower - 02-04-2018, 09:06 PM
RE: Need some hold down advice - by Mike s. - 02-05-2018, 08:14 PM
RE: Need some hold down advice - by Highpower - 02-05-2018, 08:29 PM
RE: Need some hold down advice - by Vinny - 02-06-2018, 12:10 AM
RE: Need some hold down advice - by EdK - 02-06-2018, 05:42 PM
RE: Need some hold down advice - by Vinny - 02-06-2018, 09:02 PM
RE: Need some hold down advice - by Vinny - 02-18-2018, 12:41 AM
RE: Need some hold down advice - by TomG - 02-18-2018, 09:08 AM
RE: Need some hold down advice - by Vinny - 02-18-2018, 11:01 AM
RE: Need some hold down advice - by Highpower - 02-18-2018, 03:11 PM
RE: Need some hold down advice - by Vinny - 02-19-2018, 12:19 AM
RE: Need some hold down advice - by Vinny - 03-02-2018, 09:04 PM



Users browsing this thread: 5 Guest(s)