MetalworkingFun Forum › Machining › General Metalworking Discussion v
Need some hold down advice

Thread Modes
Need some hold down advice
SteveG Offline
Sophmore
***
Posts: 130
Threads: 17
Joined: Dec 2016
Location: Melbourne, Australia
#13
02-02-2018, 08:55 PM
In a previous life the machinists would use carpet tape to hold down aluminium strip that was being milled into tapered shims using a facemill, so should work fine for your job.

Steve
Reply
Thanks given by:


Messages In This Thread
Need some hold down advice - by Vinny - 02-02-2018, 01:27 PM
RE: Need some hold down advice - by dallen - 02-02-2018, 01:52 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 02:17 PM
RE: Need some hold down advice - by wawoodman - 02-02-2018, 02:55 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 03:02 PM
RE: Need some hold down advice - by Dr Stan - 02-02-2018, 03:43 PM
RE: Need some hold down advice - by TomG - 02-02-2018, 04:16 PM
RE: Need some hold down advice - by randyc - 02-02-2018, 04:38 PM
RE: Need some hold down advice - by Highpower - 02-02-2018, 05:31 PM
RE: Need some hold down advice - by f350ca - 02-02-2018, 05:47 PM
RE: Need some hold down advice - by randyc - 02-02-2018, 06:08 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 06:51 PM
RE: Need some hold down advice - by kwoodhands - 03-02-2018, 02:52 PM
RE: Need some hold down advice - by SteveG - 02-02-2018, 08:55 PM
RE: Need some hold down advice - by wawoodman - 02-03-2018, 06:41 PM
RE: Need some hold down advice - by Vinny - 02-03-2018, 07:55 PM
RE: Need some hold down advice - by TomG - 02-04-2018, 04:11 PM
RE: Need some hold down advice - by Vinny - 02-04-2018, 04:36 PM
RE: Need some hold down advice - by Highpower - 02-04-2018, 09:06 PM
RE: Need some hold down advice - by Mike s. - 02-05-2018, 08:14 PM
RE: Need some hold down advice - by Highpower - 02-05-2018, 08:29 PM
RE: Need some hold down advice - by Vinny - 02-06-2018, 12:10 AM
RE: Need some hold down advice - by EdK - 02-06-2018, 05:42 PM
RE: Need some hold down advice - by Vinny - 02-06-2018, 09:02 PM
RE: Need some hold down advice - by Vinny - 02-18-2018, 12:41 AM
RE: Need some hold down advice - by TomG - 02-18-2018, 09:08 AM
RE: Need some hold down advice - by Vinny - 02-18-2018, 11:01 AM
RE: Need some hold down advice - by Highpower - 02-18-2018, 03:11 PM
RE: Need some hold down advice - by Vinny - 02-19-2018, 12:19 AM
RE: Need some hold down advice - by Vinny - 03-02-2018, 09:04 PM



Users browsing this thread: 6 Guest(s)