MetalworkingFun Forum › Machining › General Metalworking Discussion v
Need some hold down advice

Thread Modes
Need some hold down advice
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
The following 1 user Likes TomG's post:
randyc (02-02-2018)
#7
02-02-2018, 04:16 PM
I've used double sided tape before with good success. Just tape them down to a sub plate and clamp it to the table. Ordinary Scotch brand tape will work fine with all that area.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:


Messages In This Thread
Need some hold down advice - by Vinny - 02-02-2018, 01:27 PM
RE: Need some hold down advice - by dallen - 02-02-2018, 01:52 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 02:17 PM
RE: Need some hold down advice - by wawoodman - 02-02-2018, 02:55 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 03:02 PM
RE: Need some hold down advice - by Dr Stan - 02-02-2018, 03:43 PM
RE: Need some hold down advice - by TomG - 02-02-2018, 04:16 PM
RE: Need some hold down advice - by randyc - 02-02-2018, 04:38 PM
RE: Need some hold down advice - by Highpower - 02-02-2018, 05:31 PM
RE: Need some hold down advice - by f350ca - 02-02-2018, 05:47 PM
RE: Need some hold down advice - by randyc - 02-02-2018, 06:08 PM
RE: Need some hold down advice - by Vinny - 02-02-2018, 06:51 PM
RE: Need some hold down advice - by kwoodhands - 03-02-2018, 02:52 PM
RE: Need some hold down advice - by SteveG - 02-02-2018, 08:55 PM
RE: Need some hold down advice - by wawoodman - 02-03-2018, 06:41 PM
RE: Need some hold down advice - by Vinny - 02-03-2018, 07:55 PM
RE: Need some hold down advice - by TomG - 02-04-2018, 04:11 PM
RE: Need some hold down advice - by Vinny - 02-04-2018, 04:36 PM
RE: Need some hold down advice - by Highpower - 02-04-2018, 09:06 PM
RE: Need some hold down advice - by Mike s. - 02-05-2018, 08:14 PM
RE: Need some hold down advice - by Highpower - 02-05-2018, 08:29 PM
RE: Need some hold down advice - by Vinny - 02-06-2018, 12:10 AM
RE: Need some hold down advice - by EdK - 02-06-2018, 05:42 PM
RE: Need some hold down advice - by Vinny - 02-06-2018, 09:02 PM
RE: Need some hold down advice - by Vinny - 02-18-2018, 12:41 AM
RE: Need some hold down advice - by TomG - 02-18-2018, 09:08 AM
RE: Need some hold down advice - by Vinny - 02-18-2018, 11:01 AM
RE: Need some hold down advice - by Highpower - 02-18-2018, 03:11 PM
RE: Need some hold down advice - by Vinny - 02-19-2018, 12:19 AM
RE: Need some hold down advice - by Vinny - 03-02-2018, 09:04 PM



Users browsing this thread: 7 Guest(s)