Question on a 109 metal lathe.
#27
(10-30-2017, 04:40 PM)randyc Wrote: No one-up-man-ship intended but maybe even worse:  motorcycle in hailstorm on I-50 in Colorado, 1986; it was like riding on marbles !!!!  No windshield but I did have full face helmet.  (Needless to say I pulled off the highway at the next overpass and waited it out.)

I was on an old Suzuki Titan 500 two-stroke, uncomfortable but fast !  I'd like to have it back -

Hey,Vinny,sounds like we`ve had fun with our bikes.  I wish I had some of the ones I`ve had.

Take care ,fellow, always fun to look back to the good times. Thumbsup
Reply
Thanks given by:


Messages In This Thread
Question on a 109 metal lathe. - by buster - 09-20-2017, 06:44 PM
RE: Question on a 109 metal lathe. - by EdK - 09-20-2017, 07:04 PM
RE: Question on a 109 metal lathe. - by Vinny - 09-20-2017, 09:08 PM
RE: Question on a 109 metal lathe. - by Highpower - 09-20-2017, 11:09 PM
RE: Question on a 109 metal lathe. - by buster - 09-21-2017, 05:26 AM
RE: Question on a 109 metal lathe. - by Highpower - 09-21-2017, 11:02 AM
RE: Question on a 109 metal lathe. - by Mike E. - 09-21-2017, 11:57 AM
RE: Question on a 109 metal lathe. - by buster - 09-21-2017, 02:57 PM
RE: Question on a 109 metal lathe. - by buster - 09-22-2017, 03:40 PM
RE: Question on a 109 metal lathe. - by Mike E. - 09-21-2017, 04:16 PM
RE: Question on a 109 metal lathe. - by buster - 09-26-2017, 06:48 PM
RE: Question on a 109 metal lathe. - by buster - 09-26-2017, 06:57 PM
RE: Question on a 109 metal lathe. - by EdK - 09-27-2017, 07:04 AM
RE: Question on a 109 metal lathe. - by buster - 09-28-2017, 02:27 PM
RE: Question on a 109 metal lathe. - by buster - 10-13-2017, 07:39 PM
RE: Question on a 109 metal lathe. - by EdK - 10-13-2017, 07:56 PM
RE: Question on a 109 metal lathe. - by randyc - 10-14-2017, 08:53 PM
RE: Question on a 109 metal lathe. - by buster - 10-15-2017, 02:57 PM
RE: Question on a 109 metal lathe. - by Highpower - 10-14-2017, 09:25 PM
RE: Question on a 109 metal lathe. - by buster - 10-15-2017, 03:08 PM
RE: Question on a 109 metal lathe. - by randyc - 10-15-2017, 03:49 PM
RE: Question on a 109 metal lathe. - by Highpower - 10-15-2017, 07:37 PM
RE: Question on a 109 metal lathe. - by buster - 10-29-2017, 07:37 PM
RE: Question on a 109 metal lathe. - by Vinny - 10-30-2017, 08:51 AM
RE: Question on a 109 metal lathe. - by buster - 10-30-2017, 04:34 PM
RE: Question on a 109 metal lathe. - by randyc - 10-30-2017, 04:40 PM
RE: Question on a 109 metal lathe. - by buster - 10-30-2017, 06:29 PM
RE: Question on a 109 metal lathe. - by Vinny - 10-30-2017, 09:59 PM
RE: Question on a 109 metal lathe. - by Dr Stan - 10-30-2017, 10:17 PM
RE: Question on a 109 metal lathe. - by EdK - 10-31-2017, 09:30 AM
RE: Question on a 109 metal lathe. - by randyc - 10-31-2017, 06:17 PM



Users browsing this thread: 4 Guest(s)