Question on a 109 metal lathe.

Hello There, Guest! Register

Thread Modes

Question on a 109 metal lathe.

randyc Offline

Offline

Sophmore

Posts: 215
Threads: 22
Joined: Jul 2017
Location: Eureka, CA, USA

#21

10-15-2017, 03:49 PM

(10-14-2017, 09:25 PM)Highpower Wrote: I don't think anyone would whine about a Mazak lathe though. https://www.mazakusa.com/machines/process/turning/

Zamak gears on the other hand... http://www.chemtrend.com/material/alloys_metals/zinc

I'm a bit dislexic myself so I have that problem all the time.

Hwo says I'm dyslepcit ?

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Question on a 109 metal lathe. - by buster - 09-20-2017, 06:44 PM

RE: Question on a 109 metal lathe. - by EdK - 09-20-2017, 07:04 PM

RE: Question on a 109 metal lathe. - by Vinny - 09-20-2017, 09:08 PM

RE: Question on a 109 metal lathe. - by Highpower - 09-20-2017, 11:09 PM

RE: Question on a 109 metal lathe. - by buster - 09-21-2017, 05:26 AM

RE: Question on a 109 metal lathe. - by Highpower - 09-21-2017, 11:02 AM

RE: Question on a 109 metal lathe. - by Mike E. - 09-21-2017, 11:57 AM

RE: Question on a 109 metal lathe. - by buster - 09-21-2017, 02:57 PM

RE: Question on a 109 metal lathe. - by buster - 09-22-2017, 03:40 PM

RE: Question on a 109 metal lathe. - by Mike E. - 09-21-2017, 04:16 PM

RE: Question on a 109 metal lathe. - by buster - 09-26-2017, 06:48 PM

RE: Question on a 109 metal lathe. - by buster - 09-26-2017, 06:57 PM

RE: Question on a 109 metal lathe. - by EdK - 09-27-2017, 07:04 AM

RE: Question on a 109 metal lathe. - by buster - 09-28-2017, 02:27 PM

RE: Question on a 109 metal lathe. - by buster - 10-13-2017, 07:39 PM

RE: Question on a 109 metal lathe. - by EdK - 10-13-2017, 07:56 PM

RE: Question on a 109 metal lathe. - by randyc - 10-14-2017, 08:53 PM

RE: Question on a 109 metal lathe. - by buster - 10-15-2017, 02:57 PM

RE: Question on a 109 metal lathe. - by Highpower - 10-14-2017, 09:25 PM

RE: Question on a 109 metal lathe. - by buster - 10-15-2017, 03:08 PM

RE: Question on a 109 metal lathe. - by randyc - 10-15-2017, 03:49 PM

RE: Question on a 109 metal lathe. - by Highpower - 10-15-2017, 07:37 PM

RE: Question on a 109 metal lathe. - by buster - 10-29-2017, 07:37 PM

RE: Question on a 109 metal lathe. - by Vinny - 10-30-2017, 08:51 AM

RE: Question on a 109 metal lathe. - by buster - 10-30-2017, 04:34 PM

RE: Question on a 109 metal lathe. - by randyc - 10-30-2017, 04:40 PM

RE: Question on a 109 metal lathe. - by buster - 10-30-2017, 06:29 PM

RE: Question on a 109 metal lathe. - by Vinny - 10-30-2017, 09:59 PM

RE: Question on a 109 metal lathe. - by Dr Stan - 10-30-2017, 10:17 PM

RE: Question on a 109 metal lathe. - by EdK - 10-31-2017, 09:30 AM

RE: Question on a 109 metal lathe. - by randyc - 10-31-2017, 06:17 PM

Users browsing this thread: 3 Guest(s)