Question on a 109 metal lathe.
#11
Good evening,folks.. Done a little work on the 109. Got some questions.  The main drive pulley inside the housing has a gear on it that connect in between 3 larger gears. Well the side opiset the gear is wallowed out[I`m guessing.]  Does it have a bearing or bushing there. No indication of one.What good does that arrangement have . I can`t see any need for that. Can I just put a regular stepdown pulley there and forget the three gears.  I think the pulley is a nu.3515 according to my owners book.

Course I`d buy a new factory pulley[or used] if I could find it.The side with the gear is wore very little but the other side is twice as big. the shaft is 1/2 inch. Ebay doesn`t show anything and my book doesn`t show the gear.


Any help appreciated. Have a great rest of the week.,Everett
Reply
Thanks given by:


Messages In This Thread
Question on a 109 metal lathe. - by buster - 09-20-2017, 06:44 PM
RE: Question on a 109 metal lathe. - by EdK - 09-20-2017, 07:04 PM
RE: Question on a 109 metal lathe. - by Vinny - 09-20-2017, 09:08 PM
RE: Question on a 109 metal lathe. - by Highpower - 09-20-2017, 11:09 PM
RE: Question on a 109 metal lathe. - by buster - 09-21-2017, 05:26 AM
RE: Question on a 109 metal lathe. - by Highpower - 09-21-2017, 11:02 AM
RE: Question on a 109 metal lathe. - by Mike E. - 09-21-2017, 11:57 AM
RE: Question on a 109 metal lathe. - by buster - 09-21-2017, 02:57 PM
RE: Question on a 109 metal lathe. - by buster - 09-22-2017, 03:40 PM
RE: Question on a 109 metal lathe. - by Mike E. - 09-21-2017, 04:16 PM
RE: Question on a 109 metal lathe. - by buster - 09-26-2017, 06:48 PM
RE: Question on a 109 metal lathe. - by buster - 09-26-2017, 06:57 PM
RE: Question on a 109 metal lathe. - by EdK - 09-27-2017, 07:04 AM
RE: Question on a 109 metal lathe. - by buster - 09-28-2017, 02:27 PM
RE: Question on a 109 metal lathe. - by buster - 10-13-2017, 07:39 PM
RE: Question on a 109 metal lathe. - by EdK - 10-13-2017, 07:56 PM
RE: Question on a 109 metal lathe. - by randyc - 10-14-2017, 08:53 PM
RE: Question on a 109 metal lathe. - by buster - 10-15-2017, 02:57 PM
RE: Question on a 109 metal lathe. - by Highpower - 10-14-2017, 09:25 PM
RE: Question on a 109 metal lathe. - by buster - 10-15-2017, 03:08 PM
RE: Question on a 109 metal lathe. - by randyc - 10-15-2017, 03:49 PM
RE: Question on a 109 metal lathe. - by Highpower - 10-15-2017, 07:37 PM
RE: Question on a 109 metal lathe. - by buster - 10-29-2017, 07:37 PM
RE: Question on a 109 metal lathe. - by Vinny - 10-30-2017, 08:51 AM
RE: Question on a 109 metal lathe. - by buster - 10-30-2017, 04:34 PM
RE: Question on a 109 metal lathe. - by randyc - 10-30-2017, 04:40 PM
RE: Question on a 109 metal lathe. - by buster - 10-30-2017, 06:29 PM
RE: Question on a 109 metal lathe. - by Vinny - 10-30-2017, 09:59 PM
RE: Question on a 109 metal lathe. - by Dr Stan - 10-30-2017, 10:17 PM
RE: Question on a 109 metal lathe. - by EdK - 10-31-2017, 09:30 AM
RE: Question on a 109 metal lathe. - by randyc - 10-31-2017, 06:17 PM



Users browsing this thread: 3 Guest(s)