Harrison Milling Machine
#19
As far as paint goes, steer clear of two pack, I use either cellulose or synthetic high build primer, followed by synthetic alkyd enamel tractor paint, such as "Tractol" thinned with white spirit, and sprayed. Very oil resistant once cured and high gloss as well.
Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:


Messages In This Thread
Harrison Milling Machine - by Zoot Suit - 05-01-2017, 11:31 AM
RE: Harrison Milling Machine - by Mike E. - 05-01-2017, 12:31 PM
RE: Harrison Milling Machine - by Zoot Suit - 05-01-2017, 12:55 PM
RE: Harrison Milling Machine - by EdK - 05-01-2017, 04:21 PM
RE: Harrison Milling Machine - by Roadracer_Al - 05-01-2017, 04:24 PM
RE: Harrison Milling Machine - by TomG - 05-01-2017, 05:19 PM
RE: Harrison Milling Machine - by f350ca - 05-01-2017, 07:59 PM
RE: Harrison Milling Machine - by Mayhem - 05-02-2017, 06:36 AM
RE: Harrison Milling Machine - by Pete O - 05-02-2017, 07:20 AM
RE: Harrison Milling Machine - by Dr Stan - 05-02-2017, 11:02 AM
RE: Harrison Milling Machine - by rleete - 05-02-2017, 11:48 AM
RE: Harrison Milling Machine - by Zoot Suit - 05-02-2017, 03:03 PM
RE: Harrison Milling Machine - by f350ca - 05-02-2017, 03:44 PM
RE: Harrison Milling Machine - by hermetic - 05-02-2017, 05:01 PM
RE: Harrison Milling Machine - by hermetic - 05-02-2017, 05:04 PM
RE: Harrison Milling Machine - by Zoot Suit - 05-03-2017, 06:37 AM
RE: Harrison Milling Machine - by Zoot Suit - 05-03-2017, 01:03 PM
RE: Harrison Milling Machine - by hermetic - 05-03-2017, 05:16 PM
RE: Harrison Milling Machine - by hermetic - 05-03-2017, 05:31 PM
RE: Harrison Milling Machine - by Zoot Suit - 05-04-2017, 03:07 AM
RE: Harrison Milling Machine - by hermetic - 05-04-2017, 03:35 PM
RE: Harrison Milling Machine - by Zoot Suit - 05-04-2017, 03:40 PM
RE: Harrison Milling Machine - by Zoot Suit - 05-09-2017, 02:22 PM
RE: Harrison Milling Machine - by awemawson - 05-09-2017, 02:41 PM
RE: Harrison Milling Machine - by Zoot Suit - 05-09-2017, 03:12 PM
RE: Harrison Milling Machine - by Vinny - 05-09-2017, 04:04 PM
RE: Harrison Milling Machine - by EdK - 05-09-2017, 04:27 PM
RE: Harrison Milling Machine - by Zoot Suit - 06-10-2017, 03:17 PM
RE: Harrison Milling Machine - by TomG - 06-10-2017, 05:16 PM
RE: Harrison Milling Machine - by f350ca - 06-10-2017, 06:07 PM
RE: Harrison Milling Machine - by Pete O - 06-10-2017, 06:23 PM
RE: Harrison Milling Machine - by Pete O - 06-10-2017, 06:26 PM
RE: Harrison Milling Machine - by Zoot Suit - 06-11-2017, 02:22 AM
RE: Harrison Milling Machine - by malben - 06-11-2017, 03:03 AM
RE: Harrison Milling Machine - by mlalonde - 07-23-2018, 10:58 PM
RE: Harrison Milling Machine - by Zoot Suit - 06-11-2017, 05:46 AM
RE: Harrison Milling Machine - by Zoot Suit - 06-11-2017, 02:02 PM
RE: Harrison Milling Machine - by awemawson - 06-11-2017, 02:27 PM
RE: Harrison Milling Machine - by Zoot Suit - 06-11-2017, 02:53 PM
RE: Harrison Milling Machine - by hermetic - 06-11-2017, 03:05 PM
RE: Harrison Milling Machine - by hermetic - 06-11-2017, 03:06 PM
RE: Harrison Milling Machine - by Zoot Suit - 06-11-2017, 03:41 PM
RE: Harrison Milling Machine - by Zoot Suit - 06-19-2017, 12:03 PM
RE: Harrison Milling Machine - by awemawson - 06-19-2017, 01:17 PM
RE: Harrison Milling Machine - by Zoot Suit - 06-19-2017, 01:36 PM
RE: Harrison Milling Machine - by f350ca - 06-19-2017, 06:02 PM
RE: Harrison Milling Machine - by Vinny - 07-24-2018, 06:59 PM



Users browsing this thread: 6 Guest(s)