Boring heads for the mill
#26
I would have to agree with Tom

HSS tooling is the best way to go for the home shop ,as the cutting edge can be adjusted on the fly to suite the material being machined , learning to grinned tooling is defiantly a must ,rather than reaching for the TCT tooling ,,,much cheaper too .



RobWilsonPopcorn
Reply
Thanks given by:


Messages In This Thread
Boring heads for the mill - by DanH - 06-04-2012, 01:32 PM
RE: Boring heads for the mill - by doubleboost - 06-04-2012, 02:12 PM
RE: Boring heads for the mill - by Hopefuldave - 06-04-2012, 02:22 PM
RE: Boring heads for the mill - by DanH - 06-04-2012, 03:43 PM
RE: Boring heads for the mill - by EdK - 06-04-2012, 04:16 PM
RE: Boring heads for the mill - by f350ca - 06-04-2012, 05:23 PM
RE: Boring heads for the mill - by DaveH - 06-04-2012, 05:26 PM
RE: Boring heads for the mill - by EdK - 06-04-2012, 05:39 PM
RE: Boring heads for the mill - by DanH - 06-04-2012, 08:06 PM
RE: Boring heads for the mill - by ukazak - 06-05-2012, 01:45 AM
RE: Boring heads for the mill - by doubleboost - 06-05-2012, 05:10 AM
RE: Boring heads for the mill - by Mayhem - 06-05-2012, 06:24 AM
RE: Boring heads for the mill - by f350ca - 06-05-2012, 09:57 AM
RE: Boring heads for the mill - by Highpower - 06-05-2012, 03:45 PM
RE: Boring heads for the mill - by EdK - 06-05-2012, 03:59 PM
RE: Boring heads for the mill - by rleete - 06-05-2012, 06:56 PM
RE: Boring heads for the mill - by stevec - 06-05-2012, 07:18 PM
RE: Boring heads for the mill - by DanH - 06-05-2012, 07:28 PM
RE: Boring heads for the mill - by krv3000 - 06-06-2012, 05:05 AM
RE: Boring heads for the mill - by PixMan - 06-15-2012, 10:09 PM
RE: Boring heads for the mill - by TomG - 06-21-2012, 12:35 PM
RE: Boring heads for the mill - by DaveH - 06-21-2012, 01:43 PM
RE: Boring heads for the mill - by TomG - 06-21-2012, 02:21 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 02:45 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 01:56 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 03:02 PM
RE: Boring heads for the mill - by Keith_W - 06-22-2012, 03:33 PM
RE: Boring heads for the mill - by TomG - 06-22-2012, 05:34 PM
RE: Boring heads for the mill - by DaveH - 06-23-2012, 07:15 AM
RE: Boring heads for the mill - by PixMan - 06-22-2012, 07:10 PM
RE: Boring heads for the mill - by EdK - 06-22-2012, 07:16 PM
RE: Boring heads for the mill - by pineyfolks - 07-25-2012, 04:20 AM



Users browsing this thread: 6 Guest(s)