Machining an AR15 lower receiver

Thread Modes

Machining an AR15 lower receiver

TomG Offline

Alt. Whipping Boy

Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan

#20

06-21-2012, 01:49 PM

Supposedly, lower forgings can be purchased directly from Brass Aluminum Forging Enterprises of Ferndale, MI. for $13 each. I haven't verified this, but the link with all of the contact information is on the forum at CNCGuns.

Tom

Like Post

Thanks given by: Highpower

« Next Oldest | Next Newest »

Messages In This Thread

Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:35 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:39 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 04:47 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:58 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 05:03 PM

RE: Machining an AR15 lower receiver - by doubleboost - 06-20-2012, 04:48 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 04:55 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 05:02 PM

RE: Machining an AR15 lower receiver - by stevec - 12-01-2013, 07:28 AM

RE: Machining an AR15 lower receiver - by TomG - 06-20-2012, 05:10 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 05:32 PM

RE: Machining an AR15 lower receiver - by TomG - 06-20-2012, 05:41 PM

RE: Machining an AR15 lower receiver - by ETC57 - 06-20-2012, 06:12 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-20-2012, 07:30 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 09:30 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 01:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 12:28 AM

RE: Machining an AR15 lower receiver - by RobWilson - 06-21-2012, 09:12 AM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 01:49 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 04:19 PM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 04:33 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 04:56 PM

RE: Machining an AR15 lower receiver - by doubleboost - 06-21-2012, 03:03 PM

RE: Machining an AR15 lower receiver - by DaveH - 06-21-2012, 03:26 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 07:55 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 09:58 PM

RE: Machining an AR15 lower receiver - by RobWilson - 06-22-2012, 10:51 AM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 10:17 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 12:06 AM

RE: Machining an AR15 lower receiver - by Mayhem - 06-21-2012, 10:30 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 12:27 AM

RE: Machining an AR15 lower receiver - by TomG - 06-22-2012, 06:28 AM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 08:34 AM

RE: Machining an AR15 lower receiver - by DaveH - 06-22-2012, 09:25 AM

RE: Machining an AR15 lower receiver - by TOM REED - 06-22-2012, 09:36 AM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 04:29 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-29-2012, 08:31 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-30-2012, 02:24 AM

RE: Machining an AR15 lower receiver - by DaveH - 06-29-2012, 08:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-29-2012, 09:19 PM

RE: Machining an AR15 lower receiver - by TomG - 06-29-2012, 08:46 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-30-2012, 10:03 AM

RE: Machining an AR15 lower receiver - by ScrapMetal - 07-01-2012, 01:08 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-01-2012, 08:59 AM

RE: Machining an AR15 lower receiver - by doubleboost - 07-01-2012, 10:49 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-01-2012, 12:23 PM

RE: Machining an AR15 lower receiver - by doubleboost - 07-01-2012, 12:42 PM

RE: Machining an AR15 lower receiver - by NevadaBlue - 07-23-2012, 10:52 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-23-2012, 12:04 PM

RE: Machining an AR15 lower receiver - by d65 - 11-30-2013, 09:49 PM

RE: Machining an AR15 lower receiver - by Highpower - 12-22-2013, 07:26 AM

Users browsing this thread: 3 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me