Planer Blade Grinder
#30
They were there Pete. 1/2 inch coarse thread, just had to make the plate with slotted holes similar to the plates on the mag table for the grinder.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
Planer Blade Grinder - by f350ca - 11-18-2016, 09:49 PM
RE: Planer Blade Grinder - by dallen - 11-18-2016, 10:20 PM
RE: Planer Blade Grinder - by f350ca - 11-18-2016, 11:14 PM
RE: Planer Blade Grinder - by the penguin - 11-19-2016, 09:18 AM
RE: Planer Blade Grinder - by f350ca - 11-20-2016, 06:18 PM
RE: Planer Blade Grinder - by schor - 11-21-2016, 08:11 AM
RE: Planer Blade Grinder - by f350ca - 11-21-2016, 10:09 AM
RE: Planer Blade Grinder - by Roadracer_Al - 11-21-2016, 11:36 AM
RE: Planer Blade Grinder - by schor - 11-21-2016, 11:58 AM
RE: Planer Blade Grinder - by f350ca - 11-21-2016, 02:24 PM
RE: Planer Blade Grinder - by schor - 11-25-2016, 08:31 AM
RE: Planer Blade Grinder - by f350ca - 11-24-2016, 07:45 PM
RE: Planer Blade Grinder - by Mayhem - 11-25-2016, 10:47 AM
RE: Planer Blade Grinder - by f350ca - 11-25-2016, 02:07 PM
RE: Planer Blade Grinder - by Mayhem - 11-25-2016, 07:17 PM
RE: Planer Blade Grinder - by f350ca - 11-25-2016, 08:15 PM
RE: Planer Blade Grinder - by f350ca - 11-26-2016, 09:43 PM
RE: Planer Blade Grinder - by f350ca - 11-30-2016, 09:21 PM
RE: Planer Blade Grinder - by f350ca - 12-08-2016, 08:19 PM
RE: Planer Blade Grinder - by Mayhem - 12-08-2016, 10:05 PM
RE: Planer Blade Grinder - by f350ca - 12-08-2016, 10:47 PM
RE: Planer Blade Grinder - by Vinny - 12-08-2016, 11:14 PM
RE: Planer Blade Grinder - by Pete O - 12-09-2016, 04:54 AM
RE: Planer Blade Grinder - by f350ca - 12-09-2016, 07:35 PM
RE: Planer Blade Grinder - by EdK - 12-09-2016, 08:28 PM
RE: Planer Blade Grinder - by Pete O - 12-10-2016, 02:04 AM
RE: Planer Blade Grinder - by Roadracer_Al - 12-11-2016, 10:25 AM
RE: Planer Blade Grinder - by f350ca - 12-12-2016, 01:20 AM
RE: Planer Blade Grinder - by Pete O - 12-12-2016, 04:41 AM
RE: Planer Blade Grinder - by f350ca - 12-12-2016, 11:11 AM
RE: Planer Blade Grinder - by Pete O - 12-12-2016, 05:44 PM
RE: Planer Blade Grinder - by f350ca - 12-12-2016, 05:54 PM
RE: Planer Blade Grinder - by f350ca - 12-12-2016, 10:59 PM
RE: Planer Blade Grinder - by f350ca - 12-14-2016, 09:48 PM
RE: Planer Blade Grinder - by Vinny - 12-14-2016, 11:31 PM
RE: Planer Blade Grinder - by schor - 12-15-2016, 07:16 PM
RE: Planer Blade Grinder - by f350ca - 12-15-2016, 09:11 PM
RE: Planer Blade Grinder - by Vinny - 12-15-2016, 11:49 PM
RE: Planer Blade Grinder - by schor - 12-16-2016, 08:05 AM
RE: Planer Blade Grinder - by Mayhem - 12-16-2016, 10:42 AM
RE: Planer Blade Grinder - by Vinny - 12-16-2016, 06:53 PM
RE: Planer Blade Grinder - by schor - 12-16-2016, 06:58 PM
RE: Planer Blade Grinder - by EdK - 12-16-2016, 07:03 PM
RE: Planer Blade Grinder - by f350ca - 12-16-2016, 10:12 PM
RE: Planer Blade Grinder - by Bill Gruby - 01-06-2017, 05:05 PM



Users browsing this thread: 4 Guest(s)