MetalworkingFun Forum › Machinery › Lathes v
[HELP] 6" Fortis/Clausing lathe

Thread Modes
Help 6" Fortis/Clausing lathe
Seanlogie Offline
Freshman
**
Posts: 17
Threads: 3
Joined: Dec 2016
Location: Scotland
#16
12-09-2016, 02:21 PM
I've read somewhere ,can't remember where that there are some imperial threads that are near as not the same as some metric . Did i imagine reading this or is there some truth in it ?.

Sean
Information junkie  Thumbsup
Reply
Thanks given by:


Messages In This Thread
6" Fortis/Clausing lathe - by Seanlogie - 12-04-2016, 02:57 AM
RE: 6" Fortis/Clausing lathe - by Vinny - 12-04-2016, 03:08 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-05-2016, 02:37 AM
RE: 6" Fortis/Clausing lathe - by Pete O - 12-04-2016, 05:15 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-05-2016, 02:34 AM
RE: 6" Fortis/Clausing lathe - by Mayhem - 12-05-2016, 08:25 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-05-2016, 01:22 PM
RE: 6" Fortis/Clausing lathe - by Dr Stan - 12-05-2016, 02:17 PM
RE: 6" Fortis/Clausing lathe - by EdK - 12-05-2016, 05:16 PM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-06-2016, 05:39 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-06-2016, 06:18 AM
RE: 6" Fortis/Clausing lathe - by Mayhem - 12-06-2016, 06:30 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-06-2016, 08:32 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-09-2016, 09:54 AM
RE: 6" Fortis/Clausing lathe - by Dr Stan - 12-09-2016, 10:23 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-09-2016, 02:21 PM
RE: 6" Fortis/Clausing lathe - by EdK - 12-09-2016, 04:40 PM
RE: 6" Fortis/Clausing lathe - by Vinny - 12-09-2016, 07:36 PM
RE: 6" Fortis/Clausing lathe - by Mayhem - 12-09-2016, 08:26 PM
RE: 6" Fortis/Clausing lathe - by Vinny - 12-09-2016, 08:42 PM
RE: 6" Fortis/Clausing lathe - by Dr Stan - 12-10-2016, 01:54 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-10-2016, 01:47 AM
RE: 6" Fortis/Clausing lathe - by Pete O - 12-10-2016, 02:18 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-10-2016, 02:50 AM
RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-13-2016, 01:34 PM



Users browsing this thread: 3 Guest(s)